Fanvil BW320 User Manual Download Page 37 | Manualshive

Page: 37 / 53

background image

37

Length

Handdown Time

Specify the least reflection time of Handdown, the default is 200ms.

Output Volume

Specify Output (receiver) Volume grade.

Ring Volume

Specify Ring Volume grade

G722 Timestamps

160/20ms or 320/20ms is available

G723 Bit Rate

5.3kb/s or 6.3kb/s is available

Default Ring Type

Set up the ring by default

Signal Standard

Select Signal Standard.

VAD

Select it or not to enable or disable VAD. If enable VAD, G729
Payload length could not be set over 20ms.

4.3.4.2. Call Service

In this web page, you can configure Hotline, Call Transfer, Call Waiting, 3 Ways Call, Black
List, white list Limit List and so on.

Call Service

Field name

explanation

Hotline

Specify Hotline number. If you set the number, you can not dial
any other numbers.

No Answer Time

Specify No Answer Time

P2P IP Prefix

Set Prefix in peer to peer IP call. For example: what you want to
dial is 192.168.1.119, If you define P2P IP Prefix as 192.168.1., you
dial only #119 to reach 192.168.1.119. Default is “.”. If there is no
“.” Set, it means to disable dialing IP.

Remote Record No

Set Remote Record number. Via dialing this number, you can hear
all voice records in your VoIP server.

Do Not Disturb

Select NO Disturb, the phone will reject any incoming call, the
callers will be reminded by busy, but any outgoing call from the
phone will work well.

Ban Outgoing

If you select Ban Outgoing to enable it, and you can not dial out
any number.

Enable Call Transfer

Enable Call Transfer by selecting it.

Enable Call Waiting

Enable Call Waiting by selecting it.

Enable Three Way Enable Three Way Call

«
...
35
36
37
38
39
...
»

Summary of Contents for BW320






















































Reviews:

No comments

Related manuals for BW320

Brand: Yealink Pages: 3

Brand: AU Pages: 30

Brand: Sangoma Pages: 9

IP Vision Dialog 4425

Brand: Ericsson Pages: 136

Brand: golmar Pages: 2

Clarity Series BG1200-G

Brand: Transense Pages: 14

Brand: AT&T Pages: 37

Brand: Meriam Pages: 31

Brand: UNITe IP Pages: 116

Brand: Pantech Pages: 76

Brand: Zte Pages: 89

8120 - Pearl - GSM

Brand: Blackberry Pages: 33

Brand: Acer Pages: 56

Brand: Acer Pages: 32

Brand: Acer Pages: 56

Brand: Acer Pages: 58

Brand: Acer Pages: 32

Brand: Acer Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands