Fanvil BW320 User Manual Download Page 23 | Manualshive

Page: 23 / 53

background image

23

LAN Config

Field name

explanation

LAN IP

Specify LAN static IP.

Netmask

Specify LAN Netmask.

DHCP Service

Select the DHCP server of LAN port or not. After user modify the
LAN IP address, phone will amend and adjust the DHCP Lease
Table and save the result amended automatically according to the
IP address and Netmask. You need restart the phone and the
DHCP server setting will take effect.

NAT

Select NAT or not.

Bridge Mode

Select Bridge Mode or not: If you select Bridge Mode, the phone
will no longer set IP address for LAN physical port

，

LAN and WAN

will join in the same network.. Click “Apply”, the phone will reboot.

Notice: If you choose the bridge mode, the LAN configuration will be disabled.

4.3.2.3. Qos Config

The VOIP phone support 802.1Q/P protocol and DiffServ configuration. VLAN functionality
can use different VLAN IDs by

setting signal/voice VLAN and data VLAN. The VLAN

application of this phone is very flexible.

In chart 1, there is a layer 2 switch without setting VLAN. Any broadcast frame will be

«
...
21
22
23
24
25
...
»

Summary of Contents for BW320






















































Reviews:

No comments

Related manuals for BW320

Brand: Haier Pages: 42

Factor SPH-M260

Brand: Samsung Pages: 118

Brand: Samsung Pages: 2

Brand: Samsung Pages: 34

Brand: Avaya Pages: 6

Brand: HTC Pages: 226

Brand: Alcatel Pages: 2

Brand: UVI Group Pages: 8

Brand: Pantech Pages: 70

Brand: Sagem Pages: 61

Brand: Samsung Pages: 92

Brand: Samsung Pages: 132

Brand: Samsung Pages: 38

Brand: Samsung Pages: 157

Brand: Samsung Pages: 149

Brand: Samsung Pages: 154

Brand: Samsung Pages: 188

Brand: Samsung Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands