manualshive.com logo in svg

Fanotec MECHA C2, User Manual

Share
Download
Fanotec MECHA C2 User Manual Download Page 44

44

MECHA C2 User’s Guide

v.02.5

© 2021 FANOTEC

When MECHA is in AP or AP+STA mode, it broadcasts a SSID with a specific

name – the default name contains the word "MECHA" in it – to which the

smartphone can be connected using a password, which is 12345678 by

default.
Once the smartphone is connected to the MECHA’s SSID, the MECHA’s User

Interface can be accessed in browser at

192.168.8.1

When MECHA is in STA or AP+STA, it can also connect to the SSID of a

particular network, other than MECHA’s own SSID, and as a result the User

Interface of MECHA can also be accessed at the address given in that

particular network, like this: 192.168.1.100
The particular network can be managed by the smartphone itself, if on

smartphone a hot-spot is enabled and MECHA can connect to it.

Access the User Interface (UI) with a

Smartphone

●

Press the power button,

P

, for about 3 to 5 seconds to power on

MECHA, and wait until

- + ≡

is shown on the display.

●

To be able to connect your smartphone to MECHA’s network, MECHA
must be in AP mode. So press either

-

, to set MECHA in AP mode, or

=

, to set MECHA in AP+STA mode.

●

Tap

Settings

icon on your device.

Under

Wireless and Networks

, make

sure

Wi-Fi

is turned on, then tap

Wi-Fi

.

Tap the nettwork name that contains

MECHA

in its name, to connect the

smartphone to MECHA. The default

password for MECHA’s network is

12345678

.

●

Now MECHA’s User Interface (UI) can

be accessed on the smartphone’s

browser at:

192.168.8.1

(which is a

static IP address).

Summary of Contents for MECHA C2



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands