manualshive.com logo in svg

Fanotec MECHA C1, User Manual

Share
Download
Fanotec MECHA C1 User Manual Download Page 95

95

MECHA User’s Guide

v.06

‒ Dual Axis

© 2021 FANOTEC

Download more Presets from Server

In short, to download presets from server, make sure MECHA is connected

to the Internet, then select the option

More from server

from the

Presets

list

on the

Row

page. If the option

More from server

is not displayed in the list, it

means that MECHA is not connected to the Internet. In this case, tap/click

the

[Connect to Wi-Fi]

button at the bottom of the page, and after connecting,

refresh the page.

Step by step

:

●

On

Row

page, select the option

More from server

from the

Presets

list.

●

Provide a keyword if you want to get only certain presets, and click/tap

the

[OK]

button. The names of the presets found on the server are added

to the

Presets

list.

●

The preset name describes what the preset does, and over time you will

know which keywords to use. For example, the sequence

_P_

in a preset

name means that the preset includes a pause.

●

(S)

in a preset name means that the preset is not saved yet on MECHA.

●

Save the presets you find useful, as showed in

How to Create Your Own

Presets using the UI

section:

○

Select a preset from the

Presets

list.

○

Tap/click the

[Load]

button to load it (if the button is visible).

○

Modify the preset if necessary.

○

Save the preset with the same name, or with a different name.

Summary of Contents for MECHA C1



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands