manualshive.com logo in svg

Fanotec MECHA C1, User Manual

Share
Download
Fanotec MECHA C1 User Manual Download Page 18

18

MECHA User’s Guide

v.06

‒ Single Axis

© 2021 FANOTEC

Simple Rotations

Power on MECHA

as shown above.

●

For 45° rotations:

○

Press

<

then quickly press

1

.

○

Press

>

then quickly press

1

, for the opposite direction.

●

For 90° rotations:

○

Press

<

then quickly press

2

.

○

Press

>

then quickly press

2

, for the opposite direction.

●

For 180° rotations:

○

Press

<

then quickly press

3

.

○

Press

>

then quickly press

3

, for the opposite direction.

Note that the rotation angle for the above button combinations can be

set on the

Configuration

page.

For continuous rotation

press and hold the arrow buttons, one at a time.

For example, for continuous left rotation, press and hold

<

.

If, for some reasons, you want to

reverse the direction of horizontal

simple rotations

, you can use the

2313<

code. After this change, for

example,

<

will rotate the system to the right, and

>

, to the left. Use the

same code to cancel the change.

📹

https://youtu.be/EV0X6H1b4bw

Simple rotations - MECHA Single Axis

📹

https://youtu.be/sw1FDseF4QU

Simple rotations 2 - MECHA Single Axis

Summary of Contents for MECHA C1



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands