FALMEC Airmec Built-in 50, Instruction Booklet

Page: 21 / 22

21
MAINTENANCE
Before cleaning or carrying out maintenance operations,
disconnect the equipment by removing the plug or switching off
the main switch.
Do not use detergents containing abrasive, acidic or corrosive
substances or abrasive cloths.
Regular maintenance guarantees proper operation and performance over time.
Special attention is to be paid to the
metal anti-grease filters : frequent cleaning
of the filters and their supports ensures that no flammable grease is accumulated.
CLEANING OF EXTERNAL SURFACES
You are advised to clean the external surfaces of the hood at least once every 15
days to prevent oily substances and grease from sticking to them. To clean the
brushed stainless steel hood, the Manufacturer recommends using "Magic Steel"
wipes.
Alternatively
and for all the other types of surfaces , it can be cleaned using a
damp cloth, slightly moistened with mild, liquid detergent or denatured alcohol.
Complete cleaning by rinsing well and drying with soft cloths.
Do not use too much moisture or water around the push button
control panel and lighting devices in order to prevent humidity
from reaching electronic parts.
The glass panels can only be cleaned with specific, non-corrosive or non-abrasive
detergents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with these
instructions.
CLEANING OF INTERNAL SURFACES
Do not clean electrical parts, or parts related to the motor inside
the hood, with liquids or solvents.
For the internal metal parts, see the previous paragraph.
METAL ANTI-GREASE FILTERS
It is advised to frequently wash the metal filters ( at least once a month ) leaving
them to soak in boiling water and cleaning solution for 1 hour, taking care not to
bend them.
Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling them.
Washing in a dishwasher is permitted, however, it may cause the filter material to
darken: to reduce the possibility of this problem from happening, use low-
temperature washes (55°C max.).
To extract and insert the metal anti-grease filters see the assembly instructions.
LIGHTING (on some models)
The range hood is equipped with high efficiency, low consumption LED spotlights
with an extremely long life-span under normal use conditions.
Should the LED spotlight need to be replaced, proceed as shown in the figure.
DISPOSAL AFTER END OF USEFUL LIFE
The crossed-out trash or refuse bin symbol on the appliance means
that
the product is WEEE
, i.e. “Waste electrical and electronic
equipment'', accordingly it must not be disposed of with regular
unsorted waste (i.e. with ''mixed household waste''), but it must be
disposed of separately so that it can undergo specific processing for its
re-use, or a specific treatment, to remove and safely dispose of any substances
that may be harmful to the environment and remove the raw materials that can be
recycled. Proper disposal of these products contributes to saving valuable
resources and avoid potential negative effects on personal health and the
environment, which may be caused by inappropriate disposal of waste.
You are kindly asked to contact your local authorities for further information
regarding the designated waste collection points nearest to you. Penalties for
improper disposal of such waste can be applied in compliance with national
regulations.
INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES
The EU WEEE Directive was implemented differently in each country, accordingly,
if you wish to dispose of this appliance we suggest contacting your local authorities
or dealer to find out what the correct method of disposal is.
INFORMATION ON DISPOSAL IN NON-EUROPEAN UNION COUNTRIES
The crossed-out trash or refuse bin symbol is only valid in the European Union: if
you wish to dispose of this appliance in other countries, we suggest contacting
your local authorities or dealer to find out what the correct method of disposal is.
WARNING!
The Manufacturer reserves the right to make changes to the equipment at any
time and without prior notice. Printing, translation and reproduction, even partial, of
this manual are bound by the Manufacturer's authorisation.
Technical information, graphic representations and specifications in this manual
are for information purposes and cannot be divulged.
This manual is written in Italian. The Manufacturer is not responsible for any
transcription or translation errors.