20
2-31 dated 11-07-2002 of TC61 (sub-clause 7.12.1 meeting 15 agenda item 10.11),
the minimum distance between the cooker and lower part of the hood can be
reduced to the quota reported in the installation instructions.
Should the instructions for the gas cooker specify a greater distance, this must be
taken into consideration.
Do not install the hood outdoors and do not expose it to outdoor environment (rain,
wind, etc.).
ELECTRICAL CONNECTION
(only intended for qualified personnel)
Disconnect the equipment from electrical mains power supply
before carrying out any operations on the hood.
Ensure that the wires inside the hood are not disconnected or cut:
in the event of damage, contact your nearest Servicing
Department.
Refer to qualified personnel for electrical connections.
Connection must be carried out in compliance with the provisions of law in
force.
Before connecting the hood to the electrical mains power supply, check that:
•
voltage supply corresponds with what is reported on the data plate located
inside the hood;
•
the electrical system is compliant and can withstand the load (see the
technical specifications located inside the hood);
•
the power supply plug and cable do not come into contact with temperatures
exceeding 70 °C;
•
the power supply system is effectively and properly connected to earth in
compliance with regulations in force;
•
the socket used to connect the hood is within reach.
In case of:
•
devices fitted with cables without a plug: the type of plug to use is a
''standardised'' one. The wires must be connected as follows: yellow-green for
earthing, blue for neutral and brown for the phase. The plug must be
connected to an adequate safety socket.
•
fixed equipment not provided with a power supply cable and plug, or any other
device that ensures disconnection from the electrical mains, with an opening
gap of the contacts that enables total disconnection in overvoltage category III
conditions.
Said disconnection devices must be provided in the mains power supply in
compliance with installation regulations.
The yellow/green earth cable must not be cut off by the switch.
The Manufacturer declines all responsibility for failure to comply with the safety
regulations.
FUMES DISCHARGE
EXTERNAL EXHAUST HOOD (SUCTION)
In this version the fumes and vapours are discharged outside
through the exhaust pipe.
To this end, the hood outlet fitting must be connected via a pipe,
to an external output.
The outlet pipe must have:
•
a diameter not less than that of the hood fitting.
•
a slight slope downwards (drop) in the horizontal sections to prevent
condensation from flowing back into the motor.
•
the minimum required number of bends.
•
the minimum required length to avoid vibrations and reduce the suction
performance of the hood.
You are required to insulate the pipes if it passes through cold environments.
In the presence of motors with 800m3/h or higher, a check valve is present to
prevent external air flowing back.
Deviation for Germany:
when the kitchen hood is used at the same time as appliances that are powered by
energy other than electricity, the negative pressure in the room must not exceed 4
Pa (4 x 10-5 bar).
HOOD WITH INTERNAL RECIRCULATION (FILTERING)
In this model, the air passes through an optional filter unit in the
ceiling to be purified and recycled in the environment.
In this version the check valve must not be assembled: remove it if it is
on the air outlet fitting of the motor.
ASSEMBLY INSTRUCTIONS
only intended for qualified personnel
The hood can be installed in various configurations.
The generic assembly steps apply to all installations; for each
case, follow the specific steps provided for the required
installation.
OPERATION
WHEN TO TURN ON THE HOOD?
Switch on the hood at least one minute before starting to cook to direct fumes and
vapours towards the suction surface.
After cooking, leave the hood operating until complete extraction of all vapours and
odours.
WHICH SPEED IS TO BE SELECTED?
1st speed:
maintains the circulation of clean air with low electricity consumption.
2nd speed:
normal conditions of use.
3rd speed:
presence of strong odours and vapours.
WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?
The metal filters must be cleaned every 30 hours of operation.
For further details see the
“MAINTENANCE”
chap.
USE OF SLIDER
( MINERVA / AFRODITE / BUILT-IN )
LIGHT SWITCH
0
By placing the slider in position 0, the hood light is off
1
By placing the slider in position 1, the hood light is on
MOTOR SWITCH
0
By placing the slider in position
0
, the hood motor is off
1
By placing the slider in position
1
, the hood motor is set at minimum
speed
2
By placing the slider in position
2
, the motor is set at medium speed
3
By placing the slider in position
3
, the motor is set at high speed
The motor activation is signalled by the switching on of the red LED on the slider
MECHANICAL PUSH-BUTTON
( MERCURIO / ARTEMIDE / VULCANO / PULSAR / BUILT-IN
MAX )
Light ON / OFF
Motor speed 1
Motor speed 2
Motor speed 3
Turn off the motor
Summary of Contents for Airmec Built-in 50
