background image

14 

 

1

st

 press, Low speed 

          2

nd

 press, Medium speed 

          3

rd

 press High speed 

 

Turning off/Decreasing motor speed 

press the button and the motor begins shift to a lower speed and the LCD screen 

display the speed level. Repeating press the button, it keep on decreasing the motor 

speed  to till the cooker hood turning off. 

 

Timer

 

Press the button to set up the timer on/off function.

 

 

TROUBLESHOOTING 

Fault 

Possible Cause 

Solution 

Light on, but 
motor does not 
work 

Fan switch turned off 

Select a fan switch position. 

Fan switch failed 

Contact service center. 

Motor failed 

Contact service center. 

Light does not 
work, motor does 
not work 

House fuses blown 

Reset/Replace fuses. 

Power cord loose or 
disconnected 

Refit cord to power outlet. 
Switch power outlet on. 

Oil leakage 

One way valve and the outlet 
are not tightly sealed 

Take down the one way valve 
and seal with sealant. 

Leakage from the connection 
of chimney and cover 

Take chimney down and seal. 

Lights not 
working 

Broken/Faulty globes 

Replace globes as per this 
instruction. 

Insufficient 
suction 

The distance between the 
cooker hood and the gas top 
is too far 

Refit the cooker hood to the 
correct distance. 

The Cooker hood 
inclines 

The fixing screw not tight 
enough 

Tighten the hanging screw 
and make it horizontal. 

 

 

Summary of Contents for FAL-110-CEWG




















Reviews: