manualshive.com logo in svg

Fagor NC-200 PB - V0111, Installation Manual, Page: 34 / 58

Share
Download
Fagor NC-200 PB - V0111 Installation Manual Download Page 34

Page: 34 - Installation Manual - NC-200 PB

3.1 PARAMETER SETTING

Machine parameters PAR50, PAR51 and PAR90 enable special features of this NC.
The user may access them directly.

In initial mode, press 

 [parameter number] .

The rest can only be accessed by installers and technicians.

Press and hold 

 for at least 2 seconds, when the displays start blinking,

press 

 .

Key in the access code: 

060496 

to access the general parameters.

Once on the menu, to access a particular parameter, press:

 [Parameter number] 

The LCD display will shows the parameter number and a short description.

. If it is a general parameter, its value is only shown on the first display.

. If it is an axis parameter, each axis display will show its current value.

In this case, select the axis by pressing its key ( 

 or 

 

) and key in its

new value.

- To go to the next parameter 

saving the changes

:

Press 

 or 

  to go to the next one.

To return to the previous one, press 

- Pressing the key of the other axis ( 

 or 

 

) saves the value of the previous

axis and it goes on to edit the new selected axis.

- Pressing 

 will quit the parameter editing mode.

- If while changing the value of a parameter, 

  is pressed, the unit will ignore

the new value and will assume the previous one.

Summary of Contents for NC-200 PB - V0111



























































Reviews:

No comments