Factory Five Racing '33 Hot Rod Assembly Manual Download Page 338 | Manualshive

Page: 338 / 710

background image

337

www.factoryfive.com

508-291-3443

Reinstall the clevises and ¼” bolt then tighten the bolt so that the clevis ends are closed, this will prevent
the cable ends from coming out.

Test fit the handle with both bolts sitting in the holes. Pull the handle up. If the bolt for the rod end hits
the aluminum floor, trim the floor slightly to clear.
Remove the handle from the cockpit

Accelerator Pedal Positioning



5

/

16

”, ⅜”, ½” wrenches,

5

/

32

” hex key



Accelerator pedal components, secondary body fasteners



There are a few things to keep in mind when locating the accelerator pedal, foot clearance to the brake

pedal, clearance to the transmission tunnel height to the ball of your foot and the location for drilling
the accelerator cable hole in the firewall.

Set the seat on the floor.

«
...
336
337
338
339
340
...
»

Summary of Contents for '33 Hot Rod







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for '33 Hot Rod

Brand: GMC Pages: 140

Brand: Daihatsu Pages: 340

Brand: Daewoo Pages: 68

Brand: Hyundai Pages: 437

Brand: TBC Pages: 12

Brand: Ford Pages: 22

Brand: Sirius Satellite Radio Pages: 8

Brand: Safe Fleet Pages: 11

Brand: Camec Pages: 19

Brand: EZTRUNK Pages: 3

Brand: ACV Pages: 2

Brand: iArmor Pages: 6

Brand: Softride Pages: 4

ULTIMATE SPEED 296713

Brand: walser Pages: 10

Brand: Mercedes-Benz Pages: 373

Brand: OHIOSTEEL Pages: 2

Brand: Renault Pages: 198

Brand: Xpresskit Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands