manualshive.com logo in svg

EZ-ACCESS Modular Ramp, Assembly Manual, Page: 42 / 50

Share
Download
EZ-ACCESS Modular Ramp Assembly Manual Download Page 42

- 42 - 

6.8. 

LIGHTNING GROUND ROD:

 

 

WARNING: 

Prior to installing, ensure that any underground electrical 

conductors, natural gas lines, water/drain lines, and/or other interferences 
are located and will not hinder the installation.

 

6.8.1. 

Since aluminum can conduct electricity, the MLGRK (LIGHTNING GROUND 
ROD KIT) provides the components needed to ground a ramp system. 

6.8.2. 

Drive the grounding rod straight into the ground as close as possible (within 
1 1/2 feet maximum) to one of the support tubes leaving approximately 2" 
exposed. 

6.8.3. 

Install the brace band around support tube. Place the #8 copper wire under 
the brace band on the corner as shown (FIG. 6.22) 

6.8.4. 

Install the 5/16

″

-18 carriage bolt nut and flat washer and tighten so that wire 

is in good contact with support tube. 

6.8.5. 

Install 5/8

″

 grounding rod clamp to grounding rod. Place #8 wire between 

clamp and rod then tighten the clamp. 

FIG. 6.22

 

 

Summary of Contents for Modular Ramp



















































Reviews:

No comments