extronics iWAP XN3 X2000 Installation And Operating Manual Download Page 20 | Manualshive

Page: 20 / 29

extronics iWAP XN3 X2000 Installation And Operating Manual Download Page 20

XN3 Installation and Operating Manual

20

Figure 9: XN3 IS RF Installation Diagram

3.11

Antenna Requirements

Antennas connected to the XN3 Intrinsically Safe RF outputs must be assessed as

‘simple apparatus’ in accordance with IEC 60079

-11. Antennas supplied by

Extronics for use with the XN3 already meet these requirements. It is possible to

assess other antennas for this purpose, contact Extronics for details.

3.12

Antenna Installation

Antennas approved by Extronics for use with the XN3 may either be fitted directly

to the RF connectors of the XN3 or via a length of coaxial cable.

Enclosure earth

Hazardous area

Antenna installed to
IEC 60079-14: 2014
Clause 16.2.3

Intrinsically safe
outputs. Minimum
IP54 connection

Coaxial cable

Notes:

Marking of iWAP

XN3 must be observed
when locating antenna in
hazardous location

Conductive

mounting

structure

Antenna

Conductive parts of
antenna are earthed at
iWAP XN3 output socket
via coax cable

Coax cable

Maintain >500V

rms

isolation between conductive

parts of antenna and nearby conductive
structures in accordance with IEC60079-14:2014
clause 16.2.3

«
...
18
19
20
21
22
...
»

Summary of Contents for iWAP XN3 X2000






























Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands