XTP CrossPoint Series • Programming Guide
107
SIS Command and Response Table for Output-Endpoint-Specific
Commands
The table that starts below shows commands that affect XTP R HDMI, XTP R HD 4K,
XTP R HWP 201, XTP R HWP 201 4K, XTP SR HDMI, XTP SR HD 4K, XTP FR HD 4K, and
XTP SFR HD 4K endpoints connected through an XTP board only. The XTP CrossPoint
Series matrix switcher acts as a master, forwarding the commands to the endpoint slave.
Command Function
SIS Command
(Host to Unit to Endpoint)
Response
(Endpoint to Unit to Host)
Additional Description
XTP R HDMI, XTP R HD 4K, XTP R HWP 201, XTP R HWP 201 4K, XTP FR HD 4K,
and XTP SFR HD 4K receiver commands
Video mutes
Video mute
X@
*1B
Vmt
X@
*1
]
Mute output
X@
video (video off).
Video unmute
X@
*0B
Vmt
X@
*0
]
Unmute output
X@
video (video on).
Read video mute
X@
B
X2@]
X2@
=
1
= enable (muted)
0
= disable (unmuted) (
default
).
Global video mute
1*B
Vmt1
]
Mute all video outputs.
Global video unmute
0*B
Vmt0
]
Unmute all video outputs.
Audio routing selections
NOTES:
•
These commands select between the audio embedded in the digital video stream and the 2-channel analog audio.
•
These commands are valid only if audio breakaway switching is performed (see the
Output audio HDMI select
E
O
X@
*
X3$
AFMT
}
AfmtO
X@
*
X3$]
When audio is broken away from video,
embed audio from the
X3$
source in the
video output.
Example:
E
O3*0AFMT
}
AfmtO03*0
]
When audio is broken away from video,
use the embedded audio from the input
port when creating an audio breakaway
tie to output 3.
View output audio breakaway
selection
E
O
X@
AFMT
}
X3$]
View output audio breakaway
selection, all outputs
E
OAFMT
}
X3$
1
X3$
2
X3$
3
...
X3$
n
]
16
or
32
(
n
) sequential audio output
selections, starting from output 1.
Audio output volume
Set the audio volume to a specific
value
X@
*
X3^
V
Out
X@
•
Vol
X3^]
Example:
1*50v
Out01
•
Vol50
]
Set output 1 volume to 79%.
Increment volume
X@
+V
Out
X@
•
Vol
X3^]
Increment volume by 1 step.
Example:
1+V
Out01
•
Vol51
]
Decrement volume
X@
-V
Out
X@
•
Vol
X3^]
Decrease volume by 1 step.
Read output volume
X@
V
X3^]
Audio mutes
Mute digital audio
X@
*1Z
Amt
X@
*1
]
Mute output
X@
digital audio (audio off).
Mute analog audio
X@
*2Z
Amt
X@
*2
]
Mute output
X@
analog audio (audio off).
Mute digital and analog audio
X@
*3Z
Amt
X@
*3
]
Unmute both audio
X@
*0Z
Amt
X@
*0
]
Unmute output
X@
audio (audio on).
View audio mute status
X@
Z
X3&]
Global digital audio mute
1*Z
Amt1
]
Mute all audio digital outputs.
Global analog audio mute
2*Z
Amt2
]
Mute all analog audio outputs.
Global digital and analog audio mute
3*Z
Amt3
]
Mute all digital and analog audio outputs.
Global audio unmute
0*Z
Amt0
]
Unmute all audio outputs.
NOTE
:
X@
= Output number
01
–
16
or
32
X2@
= Enable and disable for mutes
0
= Disable
1
= Enable
X3$
= Output audio source
0
= Original HDMI audio
1
=
Embed audio
(
default
)
X3^
= Volume
00
–
64
(1 dB per step except for
0
-to-
1
, which is 13 dB) (see the
X3&
= Digital and analog audio mute status
0
= No mutes
2
= Analog audio mute
1
= Digital audio mute
3
= Analog and digital audio mute
