Extron
USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517
FAX
Extron
USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797
FAX
Extron
Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050
FAX
Extron
Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664
FAX
Extron
Japan
+81.3.3511.7655
+81.3.3511.7656
FAX
Extron
China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566
FAX
Extron
Middle East
+971.4.2991800
+971.4.2991880
FAX
a
Cut a 2" to 3" diameter hole in the ceiling tile.
b
Align the center of the receiver housing with the hole in the ceiling tile.
c
Insert the mounting screw through the receiver housing and the hole in the ceiling tile.
d
Attach the Z-bracket to the end of the screw on the back side of the ceiling tile. Replace
the ceiling tile.
e
Set the Mix DIP switch to off and the Tone DIP switch to on (VLR 102 only).
f
Pull an Ethernet cable to the receiver location, and connect one end of the cable to the
RJ-45 jack (labeled OUT) on the receiver base.
g
Align the arrow on the dome's tab with the raised arrow on the edge of the housing.
Rotate the dome to the right (clockwise) until the arrow on the tab aligns with the
raised dot on the housing.
h
Connect the other end of the Ethernet cable to the VoiceLift adapter for a VLR 102
Receiver, or to the RJ-45 jack labeled IN for a VLR 102SR Secondary Receiver.
i
Connect the VoiceLift adapter to a PoleVault switcher.
VLR 102 IR Receiver and VLR 102SR Secondary Receiver Setup Guide
VoiceLift
Adapter
PoleVault Switcher
L
R
AUX/MIX IN
1B
1A
I
N
P
U
T
S
O
U
T
P
U
T
S
2B
2A
4
3
RS-232 MLC/IR
DC VOL
4/8
Ohms
AMPLIFIED OUTPUTS
VOL/MUTE
Tx
A B C
Rx IR
12V
10V
POWER
12V
3A MAX
US
LISTED 17TT
AUDIO/VIDEO
APPARATUS
®
RGB
VIDEO
RGB
VIDEO
STEREO
ON
DUAL
MONO
HIGH
PASS
FILTER
OFF
ON
VLR 102SR
Out
Out
In
VLR 102
8
9
4
2
3
1
6
O
N
1
2
CTS-2
MIX
TONE
5
8
7
2
3
1
a
Plug the wall charger (5 V, 1 A) into a wall outlet.
b
Connect the wall charger's cable to the charging
station's power jack.
c
Place the microphone in one of the charger's slots, with
the charging contacts facing down. Charge for at least
6 hours.
N
The microphone can be left to charge for
extended periods. In maintenance mode, the
charge is retained when complete.
C
Do not charge alkaline or NiCd batteries.
68-1631-01
Rev. A
01 09
a
Set the channel using the rotary switch. A and C = 2.3 MHz;
B
and D = 2.8 MHz.
N
Each microphone must be on a different frequency. Set
the channel to C or D to disable the volume buttons.
b
Apply the Teacher or Student sticker to identify the microphone.
c
Remove the battery door, and insert the AA battery. Charge the
battery if necessary.
d
Attach the lanyard to the rotating clip. Adjust the lanyard to
position the microphone approximately 4" below the user's chin.
e
Turn the microphone on by sliding the power switch up.
f
Speak in a normal tone of voice. Do not block the microphone
port opening.
g
Adjust the volume if necessary.
5
7
3
Top
1
4
6
2
Power
Indicator
LED
VLP 102 Pendant Microphone and Charging Station Setup Guide
