background image

Installation 

Overview

1. 

Before starting, download and install the latest versions of the following software:

 

…

GUI Designer

 — for designing layouts for Extron TouchLink Pro touchpanels and third 

party touch interfaces.

 

…

Global Configurator Plus and Professional

 — for setting up and configuring the 

control processor and touchpanel.

 

…

Toolbelt

 — provides device discovery, device information, firmware updates, 

and configuration of network settings, system utilities, and user management for 
TouchLink Pro devices.

See 

Configuration Software

 on page 14.

2. 

Obtain the following network information from your network administrator:

 

…

DHCP status

 (

On

 or 

Off

). If DHCP is off, you also require

 

…

IP address

 

…

Subnet mask

 

…

Gateway

 

…

User name

 — this can be either 

admin

 or 

user

.

 

…

Password

  — by default this is 

extron

 (for either 

admin

 or 

user

).

 

…

MAC address

 — make a note of the touchpanel MAC address.

3. 

Connect cables to the units:

ATTENTION:

• 

Do not power on the touchpanels or control processors until you have read the 
Attention notice on 

page 6

.

• 

Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu les mises 
en garde 

page 6

.

 

…

Connect cables to the touchpanels (see 

Rear Panel Features

 on page 5).

 

…

Connect the power cords and power on all devices (see 

LAN/PoE Connector

 on 

page 5).

4. 

Set up the Touchpanels for Network Communication:

 

…

Connect the PC that you are using for setup, the Extron control processor, and the 
touchpanel to the same Ethernet subnetwork.

 

…

Use the 

Setup Menu

 (see page 8) or Toolbelt to set the DHCP status and, if required, 

the IP address, subnet mask, gateway, and related settings for the touchpanel.

5. 

Mount the units. There are several mounting options for either touchpanel (see 

Mounting

 on 

page 18).

NOTE:

  If you use the setup menu to configure the TLP Pro 1022M, do not mount the 

unit before configuring it. You need access to the rear panel 

Menu

 button.  

6. 

Configure the Touchpanels — the 

GUI Designer Help File,

 the 

Global Configurator Help File

and the 

Toolbelt Help File

, provide step-by-step instructions and detailed information.

The 

Global Configurator Help File

 also includes an introduction to that software and sections 

on how to start a project and configuration.

TLP Pro 1022 Series • Installation Overview

3

Summary of Contents for TLP Pro 1022T


































Reviews: