VESA Mounting (optional)
The stand for the TLP 700TV can be removed and replaced with the Extron
VM 700T kit (part #70-692-01). This bracket (see figure 7) fits into any
third-party VESA Type D 75 mm wall mount system. For more information,
see the instructions that come with the VM 700T kit.
75mm
2.95”
75mm
2.95”
Figure 7.
VMT Vesa Mount Bracket
Setup Screen
1.
Use a paper clip to press the recessed menu button (see figure 1,
8
). This opens
the setup menu at the
Main
setup page (see figure 8).
2.
Touch an area of the screen to bring it into focus and use the up and down buttons
or the volume control knob to adjust the value. Some options have a single button
and toggle between
Off
and
On
when pressed.
Use the different screen menus to adjust the following options. For more details, see
the
TLP 700MV and TLP 700TV User Guide
, which is available at
.
•
Main
(see figure 8) — This screen is used to adjust the
Sleep
timer
,
Backlight
,
Auto
Backlight
,
LED
Backlight
, and
Wake
on
Motion
functions.
•
Volume
— This screen is used to adjust the
Master
,
Click
,
Sounds
, and
Line
In
volume settings.
•
Time
— This screen is used to set up the correct time and date.
•
Network
— This screen is used to set the IP Address, the Subnet Mask, and to
enable or disable Dynamic Host Configuration Protocol (DHCP).
•
Video
— This screen provides a small video preview window and the controls to
set up the video
Contrast
,
Color
,
Brightness
, and
Tint
.
Calibration Screen
While in the
Setup
menu, press the
Menu
button a second time to open the calibration
screen (see figure
9
). When all four points have been calibrated, the screen reopens to
the
Setup
screen.
Press
Exit
to close the on-screen menus.
Figure 8.
Setup Menu
Reset Modes
The four reset modes can be initiated by using a paperclip to press the
Reset
button (see figure 1,
9
, on page 1).
NOTE:
See the
TLP 700MV and TLP 700TV User Guide
for additional details.
•
Factory Firmware Mode
— Hold the
Reset
button while applying power to reset the unit back to the base firmware shipped with
the unit.
•
Run/Stop Events Mode
— Hold the
Reset
button until the reset LED blinks once (3 seconds), then release and press
Reset
momentarily (less than 1 second) within 1 second.
This mode turns events on or off.
•
Reset All IP Settings Mode
— Hold the
Reset
button until the reset LED blinks twice (6 seconds), then release and press
Reset
momentarily (less than 1 second) within 1 second.
This mode resets the IP address, subnet, gateway, port mapping, and DHCP settings back to factory defaults. The reset LED
blinks 4 times in quick succession, confirming the reset and turning events off. If necessary, reset the IP address, using ARP and
the MAC address.
•
Reset Factory Defaults Mode
— Hold the
Reset
button until the reset LED blinks 3 times (9 seconds), then release and press
Reset momentarily (less than 1 second) within 1 second.
This mode causes a reset to factory defaults for everything except firmware.
NOTES:
•
The factory configured passwords for all accounts on this device have been set to the device serial number. Passwords
are case sensitive.
•
If the device is reset to default settings, the password will be the default password configuration. The default password
is extron.
Figure 9.
Calibration Screen
Configuring the TLP 700TV (Initial Setup)
Before using the TLP 700TV, configure it, using the on screen menus. Five
different screens (
Main
,
Volume
,
Time
,
Network
, and
Video
) can be selected
by pressing the appropriate button at the left side of the screen. Press the
Exit
button in the bottom left corner to close the menus.
3
Product Category