Quantum Ultra Videowall Processing System • Remote Configuration and Control
71
Command
ASCII Command
(Host to Processor)
Response
(Processor to Host)
Additional Description
IP Setup
NOTES:
•
Unless noted, all commands apply to LAN A.
•
After adjusting
any
IP setting, enter the network reboot command
E
1BOOT
}
for the command to take effect.
Set unit name
24
E
X11@
CN
}
Ipn
•
X11@
]
Specify a name for the unit.
NOTES:
•
Up to 15 characters are permitted. No blank or space characters are allowed.
•
No distinction is made between upper- and lowercase.
•
The
first
character must be an
alpha
character (
A-Z
,
a-z
). The
last
character
cannot
be a
hyphen
.
View unit name
E
CN
}
X11@
]
In verbose modes 2 and 3:
Ipn
•
X11@
]
View the name of the unit.
View hardware (MAC)
address for LAN A
E
1CH
}
X11*
]
In verbose modes 2 and 3:
Iph
1
*
X11*
]
View unit media access code
(MAC) address
X11*
for the
LAN A port.
View hardware (MAC)
address for LAN B
E
2CH
}
X11*
]
In verbose modes 2 and 3:
Iph
2
*
X11*
]
View unit media access code
(MAC) address
X11*
for the
LAN B port.
IP Addresses
NOTE:
After adjusting IP settings by the
CI
,
CS
, or
CG
commands, you must enter the network reboot command
E
1BOOT
}
for the command to take effect. This is not required if you use the
CISG
command.
Set DHCP to On
24
E
1DH
}
Idh
1
]
Enable Dynamic Host
Configuration Protocol (DHCP) to
enable automatic assigning of IP
addresses.
Set DHCP to Off
24
E
0DH
}
Idh
0
]
Disable DHCP automatic IP
address assignment.
View DHCP mode
E
DH
}
X1)
]
In verbose modes 2 and 3:
Idh
X1)
]
View the DHCP status: On or Off
(default).
NOTE:
Attempting to set the IP address, subnet mask, or gateway address while DHCP is on results in an
E14
error.
Set IP address
24
E
X11#
CI
}
Ipi
•
X11#
]
Set IP address
X11#
for the unit.
View IP address
24
E
CI
}
X11#
]
In verbose modes 2 and 3:
View unit IP address
X11#
.
Set subnet mask
24
E
X11(
CS
}
Ips
•
X11(
]
Set subnet mask
X11(
for the
unit.
View subnet mask
24
E
CS
}
X11(
]
View the unit subnet mask
X11(
.
KEY:
X1)
= DHCP status:
1
= On,
0
= Off (default).
X11@
= Unit name: Text string of up to 15 characters:
A-Z
,
0-9
, and hyphen (
-
).
X11#
= IP address (
nnn.nnn.nnn.nnn
). Leading zeros in each of the four octets are optional in setting values and are
suppressed in returned values.
X11*
= Hardware (MAC) address (
00-05-A6-xx-xx-xx
)
X11(
= Subnet mask (
nnn.nnn.nnn.nnn
)
Leading zeros in each of the four octets are optional in setting values, and are suppressed in returned values.
Summary of Contents for Quantum Ultra 305
Page 6: ......