manualshive.com logo in svg

Extron electronics IP Link IPL EXP 200, User Manual, Page: 39 / 52

Share
Download
Extron electronics IP Link IPL EXP 200 User Manual Download Page 39

IPL EXP I/O Series • Software-based Configuration and Control

31

Software-Based 
Configuration and 
Control

This section of the guide is divided into the following topics:

• 

Configuration and Control: An Overview

• 

Basic Setup Steps: a Guide to this Section and Other Resources

• 

Downloading the Software and Getting Started

• 

Troubleshooting

Configuration and Control: An Overview

An IPL EXP unit must be configured before use

 in order to recognize and accept 

commands and pass them on to the controlled devices. It can be configured and controlled 
via a host computer connected to the same network as the control processor (see 

LAN/

PoE and LAN/PoE+ (Ethernet) connectors and LEDs

 starting on page 18 for details 

about LAN port and cabling to connect the expansion interface to the network).

• 

Configure the expansion interface by using the Global Configurator software 
(GC Professional or GC Plus) (see the Extron 

website

 for full system hardware and 

software requirements for GC), or program it using Global Scripter.

• 

The default web pages embedded within the expansion interface provide a means 
to view general hardware information, network settings, and, if configured, project 
information. You cannot configure the expansion interface via the embedded web 
pages.

Summary of Contents for IP Link IPL EXP 200





















































Reviews:

No comments