4
68-1916-52 Rev. A
06 15
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West:
+1.714.491.1500
FAX: +1.714.491.1517
Extron USA - East:
+1.919.850.1000
FAX: +1.919.850.1001
© 2015 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners.
www.extron.com
Internal Web Pages
To configure IN1608 HDBT scalers using the factory-installed Web pages in a Web
browser (see the example to the right), connect the Ethernet port on the device to
a LAN or WAN. The default IP address is 192.168.254.254.
Extron Product Configuration Software
To configure IN1608 HDBT scalers using the Extron Product Configuration
Software (PCS), install the software (available on the Extron website,
www.extron.com
) to a PC connected to the scaler via Ethernet or front panel USB
Config port. After the installation, start the program. For full instructions, press
<F1> on the keyboard or click the
?
button in the software and select
Help File
.
Basic SIS Command Table
To configure IN1608 HDBT scalers with specific SIS commands via an RS-232,
USB, or Ethernet connection, use the Extron DataViewer utility or a control system
to send and receive SIS commands. The table below lists a selection of SIS commands. For a full list of SIS commands and variables, see the
IN1606 and IN1608 Series User Guide
at
www.extron.com
.
Command
ASCII Command
(Host to Device)
Response
(Device to Host)
Additional Description
Select audio and video input
X!
!
In
X!•
All
]
Selects audio and video input
X!
.
Select video input only
X!
&
In
X!•
RGB
]
Selects the video only input
X!
.
Select audio input only
X!
$
In
X!•
Aud
]
Selects the audio only input
X!
.
Execute Auto-Image
™
A
Img0
]
Executes an Auto-Image on the current input.
Execute Auto-Image and fill
1*A
Img1
]
Executes an Auto-Image and fills the output.
Execute Auto-Image and follow
2*A
Img2
]
Executes an Auto-Image and maintains the aspect ratio of
the current input.
Mute video to black
1B
Vmt1
]
Mutes the video and displays a black output.
Mute video and sync
2B
Vmt2
]
Mutes the video and sync output.
Unmute video and sync
0B
Vmt0
]
Unmutes the video.
NOTE:
By default, setting the audio mute with the following commands affects all outputs (configurable through group masters).
Set master audio mute
E
D7*
X(
GRPM
}
GrpmD07*
X(]
Enable or disable master audio mute.
View master audio mute status
E
D7GRPM
}
X(]
View the current master audio mute status.
Enable executive mode 1
1X
Exe1
]
Locks the entire front panel.
Enable executive mode 2
2X
Exe2
]
Locks the front panel except for input selection and volume
control.
Disable executive modes
0X
Exe0
]
Allows all front panel adjustments and selections.
Set scaler IP address
EX4)
CI
}
Ipi
•X4)]
Specifies a new scaler IP address.
Set scaler DHCP mode
EX(
DH
}
Idh
X(]
Enables or disables DHCP (
0
= default).
Set subnet mask
EX4!
CS
}
Ips
•X4!]
Specifies a new subnet mask.
Set gateway IP address
EX4@
CG
}
Ipg
•X4@]
Specifies a new gateway IP address.
Reboot network
E
2BOOT
}
Boot2
]
Restarts the network connection after IP or DHCP changes.
NOTE:
IP settings will not take effect until the
E
2BOOT
}
command is executed.
NOTES:
X!
= Input selection (
1-8)
X(
= Enable or disable (
0
= off or disabled;
1
= on or enabled)
X4)
= IP address (
xxx.xxx.xxx.xxx
;
192.168.254.254
= default)
X4!
= Subnet mask (
xxx.xxx.xxx.xxx
;
255.255.0.0
= default)
X4@
= Gateway address (
xxx.xxx.xxx.xxx
;
0.0.0.0
= default)
Firmware Updates
Download firmware updates from the Extron website and upload them via the internal Web pages or the Extron Firmware Loader program.