2
IN1608 HDBT Series • Setup Guide (Continued)
Step 2
—
Connect inputs
a.
Connect analog video sources to the VGA connectors (see figure 1,
B
on page 1).
b.
Connect digital HDMI or DVI (with an appropriate adapter) sources to the HDMI connectors (see figure 1,
C
).
c.
Connect a DTP transmitter to the DTP input connectors (see figure 1,
D
). For cable wiring and recommendations, see
Twisted Pair
Recommendations for DTP and HDBaseT Communication
below.
Signal LED
—
Lights green when the unit is receiving an active video signal from a DTP transmitter.
Link LED
—
Lights amber when a valid link is established to a DTP transmitter.
d.
To pass serial or infrared data, connect the control device to the RS-232 and IR Over DTP captive screw connectors (see
RS-232 and IR
Over TP Wiring
on page 3).
e.
Connect analog audio input sources to the 5-pole captive screw connectors (see figure 1,
E
). See
Audio Wiring
on page 3.
f.
Connect Mic/Line audio input sources to the 3-pole captive screw connectors (see figure 1,
F
).
Step 3
—
Connect outputs
a.
Connect an HDBaseT-compatible device to the HDBT output connector (see figure 1,
G
). For cable wiring and recommendations, see
Twisted Pair Recommendations for DTP and HDBaseT Communication
below.
Signal LED
—
Lights green when the scaler is outputting active video.
Link LED
—
Lights amber when a valid link is established between the scaler and HDBaseT sink.
b.
To pass serial or infrared data, connect a control device to the RS-232 and IR Over HDBT captive screw connector (see
RS-232 and IR
Over TP Wiring
on page 3).
c.
Connect suitable video displays to the HDMI connectors (see figure 1,
H
).
d.
Connect analog audio output devices to the 3.5 mm, 5-pole captive screw connectors (see figure 1,
I
). See
Audio Wiring
on page 3.
e.
For SA and MA models, connect an audio output device to the 5 mm, 4-pole or 2-pole captive screw connector (see figure 1,
J
).
Step 4
—
Connect control devices
a.
To control non-IPCP models through Ethernet, connect a LAN or WAN to the LAN connector (see
M
on page 1). For the IPCP models,
connect a LAN or WAN to any of the LAN connectors on the IPCP Pro control processor (see figure 1,
L
). The default IP address is
192.168.254.254. The default subnet mask is 255.255.0.0.
b.
For serial RS-232 control, connect a host device to the 3-pole captive screw connector (see figure 1,
K
). The default baud rate is 9600.
c.
For control through USB, connect a host device to the front panel USB mini-B port (see figure 2,
A
on page 3).
Step 5
—
Set up the IPCP Pro control processor (IPCP models only)
See the
IPCP Pro Series Setup Guide
for installation details.
Step 6
—
Connect power
Connect a 100 to 240 VAC, 50-60 Hz power source to the AC power connector (see figure 1,
A
).
Twisted Pair Recommendations for DTP and HDBaseT Communication
Extron recommends using the following practices to achieve full transmission distances and reduce
transmission errors:
•
Use Extron XTP DTP 24 SF/UTP cable for the best performance. At a minimum, Extron recommends
24 AWG, solid conductor, STP cable with a minimum bandwidth of 400 MHz.
•
Terminate cables with shielded connectors to the TIA/EIA-T568B standard (shown to the right).
•
Limit the use of more than two pass-through points, which may include patch points, punch down
connectors, couplers, and power injectors. If these pass-through points are required, use shielded
couplers and punch down connectors.
ATTENTION:
•
Do not connect these connectors to a computer or telecommunications network.
•
Ne connectez pas ces ports à des données informatiques ou à un réseau de télécommunications.
•
DTP remote power is intended for indoor use only. No part of the network that uses DTP remote power should be routed outdoors.
•
L’alimentation DTP à distance est destiné à une utilisation en intérieur seulement. Aucune partie du réseau qui utilise l’alimentation DTP
à distance ne peut être routée en extérieur.
NOTE:
When using shielded twisted pair cable in bundles or conduits, consider the following:
•
Do not exceed 40% fill capacity in conduits.
•
Do not comb the cable for the first 20 meters, where cables are straightened, aligned, and secured in tight bundles.
•
Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
•
Separate twisted pair cables from AC power cables.
TIA/EIA-T568B
Pin Wire Color
1
White-orange
2
Orange
3
White-green
4
Blue
5
White-blue
6
Green
7
White-brown
8
Brown
12345678
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A
T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown