FOX3 SR 201 Scaling Receiver • SIS Configuration and Control
29
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
IP address
Set IP address
E
X1!
CI
}
Ipi
•
X1!]
View IP address
E
CI
}
X1!]
KEY:
X1!
= IP address
xxx
.
xxx
.
xxx
.
xxx
RS-232 COMM settings
Set serial port parameters
EX1^
*
X1@
,
X1#
,
X1$
,
X1%
CP
}
Cpn
X1^
•
Ccp
X1@
,
X1#
,
X1$
,
X1%]
KEY:
X1@
= Baud rate
300
−
115200
baud (
9600
default
)
X1#
= Parity
o
dd,
e
ven,
n
one (
default
),
m
ark,
s
pace (only the first letter required)
X1$
= Data bits
7
,
8
(
default
)
X1%
= Stop bits
1
(
default
),
2
X1^
= UARTs
1
= endpoint
Resets
Erase all files from flash memory
E
ZFFF
}
Zpf
]
Removes files created in user space.
Reset unit settings
E
ZXXX
}
Zpx
]
Resets unit to factory default.
Absolute system reset (retain IP)
E
ZY
}
Zpy
]
Same as
E
ZQQQ except excludes IP
settings.
Absolute system reset
E
Z
QQQ
}
Zpq
]
Master Reset, resets IP address and
subnet mask to default.
IP system reset
E
1Z
QQQ
}
Zpq1
]
Resets only IP settings.
Reset audio gain and attenuation
E
ZA
}
Zpa
]
Reset audio gain & attenuation to default
levels.
Global unsolicited responses
Input change
Reconfig
]
Any change of the input frequency or a
power cycle.
Fiber link
Sts02*
X1*
*
X2*]
Any change in fiber link status.
Input video signal presence
SigI
X$]
Any change in input signal status.
Input HDCP
HdcpI
X^]
Any change in input HDCP status.
Output HDCP
Hdcp
O
X&]
Any change in output HDCP status.
Audio input status
Sts05*
X%]
Displays input audio selection status.
KEY:
X$
= Input video signal status
0
= Not detected
1
= Detected
X%
= Input audio status
0
= Not detected
1
= Detected
X^
= Input HDCP status
0
= No source detected
1
= Source with HDCP detected
2
= Source with no HDCP present
X&
= Output HDCP status
0
= No active sink detected
1
= Sink detected, output signal encrypted
2
= Sink detected, output signal not encrypted
X1*
= Active fiber link
1
= SFP A
2
= SFP B
X2*
= Fiber Link detection (SPF A/B IN LED)
0
= Not detected
1
= Detected
NOTE:
SFP A and SFP B OUT LED is always active
Audio output volume
Set volume
X2^
V
Vol
X2^]
Increment
+V
Vol
X2^]
Decrement
-V
Vol
X2^]
View volume status
V
Verbose mode 2/3
X2^]
Vol
X2^]
KEY:
X2^
= Audio output volume
Volume adjustment range:
0%
to
100%
(
1
dB per step
0%
to
100%
, default
100%
)
Summary of Contents for FOX3 SR 20
Page 2: ...Safety Instructions...
Page 6: ......