2
FOX T UWP 302 • Installation Guide (Continued)
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West
Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX
+1.919.850.1001 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91-80-3055.3777
+91 80 3055 3737 FAX
©
2017 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners.
68-2092-50
Rev. B
04 17
Step 4
—
Making Front Panel Connections
F
Connect a source device to the HDMI connector.
TIP:
Use an Extron LockIt
®
Lacing Bracket to secure
HDMI cables to the HDMI connector.
G
Connect a video source to the Computer Input connector.
H
Connect an audio source to the 3.5 mm TRS jack.
Operation
Remote Control
Connect a host device, such as a computer, to the mini-USB type B
config port for serial control of the FOX T UWP 302. Use SIS commands or install the FOX Extenders Control Program
from the
Extron Software Products
DVD or check the Extron website,
, for the latest version (see the
FOX T UWP 302 User Guide
for remote control details).
Reset button
Press and hold the Reset button on the front panel to enter reset mode 1 or 5. If necessary, unscrew the screws
connecting the faceplate to the enclosure and remove the faceplate to access the Reset button.
Reset Mode Summary
Mode Activation
Result
Purpose/Notes
Factory Reset
(Mode 1)
Hold the Reset button down while
applying power to the device.
NOTE:
After a mode 1 reset,
update the device with the
latest firmware version. DO NOT
operate the firmware version
that results from this mode
reset.
z
The device reverts to the factory default firmware.
z
All user files and settings (audio adjustments,
audio input selection, input selection,
auto-switch mode, picture adjustments, and
input video format) are maintained.
Use mode 1 to roll back
to factory firmware for
a single power cycle if
an incompatibility issue
arises.
Reset to Factory
Defaults (Mode 5)
Hold the Reset button down for about
9 seconds or until the Power LED
blinks three times. Then press the
Reset button momentarily
(for <1 second) within 1 second.
z
Mode 5 performs a complete reset to factory
defaults except for firmware.
z
Resets all user modifiable configurations to
default values including real-time adjustments.
z
The power LED blinks 4 times in quick
succession during the reset.
Use mode 5 to start over
with configuration or
uploading.
NOTE:
This is
equivalent to SIS
command
ZXXX
.
Indicators
Link 1 and Link 2 LEDs
—
Light to indicate fiber light presence.
Power LED
—
Lights when the device receives 12 V from an external power supply.
PC LED
—
Lights when PC input is detected.
HDMI LED
—
Lights when HDMI input is detected.
HDCP LED
—
Lights if the HDMI input signal is HDCP-encrypted.
Audio LED
—
Lights when the device detects audio with the selected input. If the selected input has an analog audio
signal above -44 dBV, the Audio LED lights immediately, but turns off only after the audio signal level drops below the
threshold continuously for 10 seconds. If the selected input has digital embedded audio, the Audio LED lights and
remains lit as long as the digital audio signal is detected.
POWER
PC
HDMI
HDCP
AUDIO
CONFIG
RESET
LINK
1
LINK
2
LINK 1
LINK 2
HDMI INPUT
AUDIO INPUT
COMPUTER INPUT
POWER
RESET
CONFIG
PC
HDMI
HDCP
AUDIO
f
F
F
F
F
F
F
F
F
F
F
G
G
G
G
G
G
G
G
G
G
H
H
H
H
H
H
H
H
H
H