Extron electronics FLEX55 AC Plus USB 130 US Setup Manual Download Page 1

1

IMPO

RTAN

T:

IMPO

RTAN

T:

Go to www

.extron.com f

or the complete 

user guide

, installation instructions,

 and 

specifications bef

ore connecting the 

product to the po

wer sour

ce.

FLEX55 AC+USB 130 US • Setup Guide

The Flex55 AC+USB 130 US Power Module provides AC, USB Type-A and USB Type-C power outlets for powering 
and charging compatible mobile devices. The following guide provides the steps to install and secure the power 
module to select Flex55 and Cable Cubby enclosures (see the ATTENTION below before installing the power 
module).
The power module supplies up to 29.5 total watts.

NOTE:

  To view the power specifications, see 

www.extron.com

.

Front Panel and Side Features

USB CHARGER

120V

50-60Hz 6A MAX

~

C

C

B

Front View

Side View

A

USB CHARGER

120V

50-60Hz 6A MAX

~

C

C

B

Front View

Side View

A

Figure 1. 

Flex55 AC+USB 130 US Power Module

A

 

USB Power Outlets

• 

USB Type-A — supports up to 10 watts (5VDC up to 2A). When both USB ports are used, the Type-A port 
drops to 0.5A.

• 

USB Type-C — supports up to 27 watts. 

B

 

AC Power Outlet

 — 

supports 120VAC, 50 to 60Hz, 6A Max.

C

 

Mounting Clips

 — 

there are four mounting clips on the unit, two on the top side of the module and two on the 

bottom. These help secure the unit to the mounting frame or bracket.

 ATTENTION:

 

• 

Always consult with a professional installer.

• 

Toujours consulter un installateur professionnel.

• 

Follow all national and local building and electrical codes that apply to the installation site.

• 

Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de 
l’installation.

• 

The installation must always be in accordance with the applicable provisions of National Electrical Code 
ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not 
be permanently fixed to building structure or similar structure.

• 

Cette installation doit toujours être conforme aux dispositions applicables du Code américain de l’électricité 
(National Electrical Code) ANSI/NFPA 70, article 725, et du Code canadien de l’électricité, partie 1, section 
16. La source d’alimentation ne devra pas être fixée de façon permanente à une structure de bâtiment ou à 
une structure similaire.

Summary of Contents for FLEX55 AC Plus USB 130 US

Page 1: ... to 27 watts B AC Power Outlet supports 120VAC 50 to 60Hz 6A Max C Mounting Clips there are four mounting clips on the unit two on the top side of the module and two on the bottom These help secure the unit to the mounting frame or bracket ATTENTION Always consult with a professional installer Toujours consulter un installateur professionnel Follow all national and local building and electrical co...

Page 2: ...ex55 compatible enclosure Figure 2 Installing the Flex55 AC USB 130 US USB CHARGER 120V 50 60Hz 6A MAX Extron Flex55 AC USB 130 US Extron Cable Cubby F55 UT enclosure Insert the module into the enclosure frame or bracket Connect any additional devices or modules Connect to power source 2 4 3 1 Extron Cable Cubby F55 UT enclosure Using cutting pliers carefully snip and remove either the center left...

Page 3: ...d pry tool This process applies to any compatible Flex55 and Cable Cubby enclosure USB CHARGER 120V 50 60Hz 6A MAX 1 Locking Tab Insert pry tool at the locking tab location 1 Unlock the other locking tabs if applicable and remove the module Pivot the pry tool away from the module to unhook each locking tab from the mounting bracket 2 3 Figure 3 Flex55 AC USB 130 US Power Module Removal ...

Page 4: ...ccessibility and related topics see the Extron Safety and Regulatory Compliance Guide on the Extron website 2021 Extron All rights reserved www extron com All trademarks mentioned are the property of their respective owners Worldwide Headquarters Extron USA West 1025 E Ball Road Anaheim CA 92805 800 633 9876 ...

Reviews: