Extron electronics eBUS 110 D Setup Manual Download Page 6 | Manualshive

Page: 6 / 14

Extron electronics eBUS 110 D Setup Manual Download Page 6

6

eBUS Button Panel Decorator-Style Series • Setup Guide (Continued)

Step 4: Set the eBUS ID

Up to eight devices can be connected to one control processor. In order for
the control processor to be successfully configured, each device connected to
the same control processor must have a unique six-bit, eBUS ID, which is set
with the DIP switch assembly on the side panel of the EBP (figure 8,

1

). If two

or more modules have the same eBUS ID, address conflicts may cause one or
more of the panels to not be recognized by the IPCP Pro control processor.
Various combinations of the six DIP switches being set to On or Off, provide 64
addresses: 0 is a reserved eBUS ID and the configurable eBUS ID range is 1
through 63 (see the table on the two following pages). The section below shows
an example of binary to decimal conversion.

1

1

Figure 8.

Decorator-style eBUS
Panel DIP Switches

eBUS ID Setup

Dip Switch

Position
Decimal

Off

1

2

5

=32

2

Off

2

4

=16

5

On

2

1

=2

4

Off

2

2

=4

3

Off

2

3

=8

6

Off

2

0

=1

Slide

1 2 3 4 5 6

ON

M

S

B

L

S

B

BUS ID

Figure 9.

eBUS ID Setup

Add the decimal numbers for each of the DIP switches that are set to

On

to obtain the address of the device. In figure 9, only DIP

switch 5 is on and the rest are off, which means the address for the device in figure 9 is 0+0+0+0+2+0 = 2.

NOTES:

•

Any address can be used except address 0 (binary: 000000), which is reserved (as the address of the controller) and
may not be used.

•

Switch 1 (on the left) is the highest value (32, the most significant bit) and is labelled

MSB

.

•

Switch 6 (on the right) is the lowest value (1, the least significant bit) and is labelled

LSB

.

•

Up

= on =

1

,

Down

= off =

0

The following table shows the factory default eBUS IDs and the corresponding addresses for the decorator-style models. These
IDs can be changed to any valid value.

Model

Address

eBUS ID

EBP 103 D

23

010111

EBP 105 D

2

000010

EBP 106 D

1

000001

EBP 106P D

13

001101

EBP 108 D

7

000111

EBP 110 D

8

001000

EBP 111 D

9

001001

EBP NAV D

18

010010

EBP VC1 D

17

010001

EBP VC2 D

15

001111

The table on the following two pages shows the DIP switch settings for all 64 possible addresses.

«
...
4
5
6
7
8
...
»

Summary of Contents for eBUS 110 D















Reviews:

No comments