Extron electronics DTP CrossPoint 4K Series, Setup Manual

Page: 18 / 44

10 DTP CrossPoint 4K Series • Installation
Q
LAN (Ethernet) port
(non-IPCP model) — If desired,
LAN
connect a network WAN or LAN hub, a control system,
or a computer to the Ethernet RJ-45 port (see
TP
connectors on
page 12
to wire the connector).
NOTE:
The factory default IP address is 192.168.254.254.
R
IPCP control processor
(IPCP models) — The IPCP models
include a built-in control processor that can control and monitor
a variety of external devices. The IPCP offers RS-232 and
IR-based control, relays, and digital I/O controls. See the
IPCP
Pro Series Setup Guide
, included with the switcher, to make
all connections and to configure and operate the IPCP control
processor.
S
Remote port
— Plug a serial RS-232 device into the
Tx Rx G
REMOTE
matrix switcher via this 3.5 mm, 3-pole captive screw
connector for remote control of the switcher (see
RS-232 and IR connectors on page 15 to wire the
connector).
Switcher Reset
50-60 Hz
100-240V ~
--A MAX
RESET
DTP CROSSPOINT 108 4K
Tx Rx RTS CTS G Tx Rx G Tx Rx G
EXP
+48V
MIC/LINE
1
1 3
2 4
2
3
4
LINK
LAN 2
LAN 1
LAN 3
R
AUDIO OUTPUTS
AMP OUTPUT
CONTROL
1 2 3 4 G
DIGITAL I/O COM 3 COM 2
AUDIO INPUTS
COM 1
S
DMP EX
PA
NSION
S G G
1 1 2 2 C 3 4 C -S G +S +V
PWR OUT = 6W
1
L R
1
L R
3
L R
3
L R
5
L R
2
L R
4
L R
2
L R
4
L R
6
L R
IR/SERIAL eBUS RELAYS
1
CLASS 2 WIRING
70V
1 2 3 4 5A 6A
XTP
DTP
HDBT
OUTPUTS
SIG LINK
OUT
5B 6B 6
XTP
S/PDIF
OUT
DTP
HDBT
Tx
XTP
DTP
HDBT
7 8
XTP
DTP
HDBT
RS-232 IR
Tx Rx Tx Rx G
RS-232 IR
Tx Rx Tx Rx G
OVER TP
RS-232 IR
Tx Rx Tx Rx G
RS-232 IR
Tx Rx Tx Rx G
OVER TP SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
XTP
DTP
XTP
DTP
1 2 3 4 5 7 8 6
INPUTS INPUTS
XTP
DTP
XTP
DTP
9 10
RS-232 IR
Tx Rx Tx Rx G
OVER TP
RS-232 IR
Tx Rx Tx Rx G
RS-232 IR
Tx Rx Tx Rx G
OVER TP
RS-232 IR
Tx Rx Tx Rx G
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
Tx Rx G
REMOTE
LAN
T
Figure 10. Reset button and LED
50-60 Hz
100-240V ~ -- A MAX
+48V
MIC/LINE
1 1 3
2 4
2
3
4
EXP
DTP CROSSPOINT 84 4K
AUDIO OUTPUT
S
AUDIO INPUTS
DMP EX
PA
NSION
1
L R
1
R
3
L R 3
L L R
5
L R
2 L R 4 L R
2
L R
4
L R 6 L R
AMP OUTPUT
CLASS 2 WIRING
1
100V
1 2
1 2 3 4 5 6
3A 4A 4B
RS-232 IR
RS-232 IR
Tx Rx Tx Rx G
Tx Rx Tx Rx
XTP
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT HDBT
G
7
8
RS-232 IR
Tx Rx Tx Rx G
RS-232 IR
Tx Rx Tx Rx G
OVER TP
OVER TP
INPUTS
OUTPUT
S 3B
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
4
S/PDIF
OUT
R
CONTROL
Tx Rx RTS CTS G
1 2 1 2
S G S G
C 3 4 C +V
PWR OUT = 6W
+V D -S +S
Tx Rx G Tx Rx G 1 2 3 4 G
COM 1 COM 3 COM 2 DIGITAL I/O
LAN 1
LAN 2 LAN 3
IR/SERIAL RELAYS DIGITAL I/O
Tx Rx G
REMOTE
RESET
T
Figure 11. Reset button and LED
T
Switcher Reset button and LED — Initiates four levels of
matrix switcher reset. For different reset levels, press and hold
the recessed
Reset
button while the switcher is running or
while you power up the switcher.
See the
DTP CrossPoint 4K Series User Guide
, at
www.extron.com
.