manualshive.com logo in svg

EXTREME SWITCHING 4450GTX-HTPWR+, Installation Job Aid

The "EXTREME SWITCHING 4450GTX-HTPWR+" Installation Job Aid manual is a comprehensive guide designed to assist users in seamlessly installing and configuring the product. Download it for free from our website to access detailed instructions, diagrams, and troubleshooting tips for a hassle-free installation experience.

Share
Download
background image

Figure 1: 1000W AC power supply

Connector

The 1000W AC power supply uses an IEC 60320 C16 AC power cord connector. The AC power

cord is in close proximity to the hot air exhaust, and supports high operating temperatures.

Figure 2: IEC 60320 C16 connector

Power over Ethernet Plus specifications

Table 2: VSP 4450GTX-HT-PWR+ model

0°C to 50°C

50°C to 70°C

1 PSU

860W

400W

2 PSU

1660W

832W

Table 3: VSP 4450GTX-HT-PWR+ model with 1 PSU

0°C to 50°C

50°C to 70°C

PoE support on

48 ports

23 ports

PoE+ support on 26 ports

13 ports

November 2017

Installation Job Aid for VSP 4450GTX-HT-PWR+

9

Summary of Contents for 4450GTX-HTPWR+












Reviews:

No comments

Related manuals for 4450GTX-HTPWR+

Brands by name

Popular brands

Load more brands