EXTREME SWITCHING 4450GTX-HTPWR+ Installation Job Aid Download Page 11

Page: 11 / 11

Table 5: International power cord specifications

Country and Plug Specification

Specifications

Typical Plug

Continental Europe:

• CEE7 standard VII male plug

• Harmonized cord (HAR marking on the outside of the cord

jacket to comply with the CENELEC Harmonized
Document HD-21)

• 220 or 230VAC

• 50 Hz

• Single phase

United States of America, Canada, and Japan:

• NEMA5-15P male plug

• UL-recognized (UL stamped on cord jacket)

• CSA-certified (CSA label secured to the cord)

• 100 or 120VAC

• 50–60 Hz

• Single phase

United Kingdom:

• BS1363 male plug with fuse

• Harmonized cord

• 240VAC

• 50 Hz

• Single phase

Australia:

• AS3112-1981 male plug

• 240VAC

• 50 Hz

• Single phase

Danger:

Using power cords with a proper grounding path

Use only power cords that have a grounding path. Without a proper ground, a person who
touches the switch is in danger of receiving an electrical shock. Lack of a grounding path to the
switch can result in excessive emissions.

November 2017

Installation Job Aid for VSP 4450GTX-HT-PWR+

Summary of Contents for 4450GTX-HTPWR+












Search results

Summary of Contents for 4450GTX-HTPWR+

Reviews:

Related manuals for 4450GTX-HTPWR+

Brands by name

Popular brands

EXTREME SWITCHING 4450GTX-HTPWR+, Installation Job Aid

Search results

Summary of Contents for 4450GTX-HTPWR+

Reviews:

Related manuals for 4450GTX-HTPWR+

Brands by name

Popular brands