manualshive.com logo in svg

Extreme Networks ExtremeWireless AP560i, Installation Manual, Page: 42 / 46

Share
Download
Extreme Networks ExtremeWireless AP560i Installation Manual Download Page 42

Access Point Specifications

Physical specifications

Item

Description

Dimensions

11.3 in. × 10 in. × 2.9 in. (288 mm × 254 mm × 75 mm)

Housing

8.99 lbs. (4.08 kg)

IP rating

IP67

LAN Ethernet

1 × 100/1000/2500/5000 Mbps auto-negotiation Ethernet port,

RJ45

1 × 10/100/1000 Mpbs auto-negotiation Ethernet port, RJ45

Console port

RJ45

USB port

USB 3.0 port, type A for purpose built modules

PoE failover

Redundant PoE capable

LEDs

Two top mounted LEDs and multiple LED radio indicators

Energy efficiency

802.3az energy-efficient Ethernet

Anti-theft locks

Kensington lock

Security hanger

Environmental specifications

Item

Description

Operating temperature

-40°C to +55°C (-40° F to +131° F)

Humidity

0 – 95% (non-condensing)

Storage and transportation temperature

-40°C to +70°C (-40° F to +158° F)

Electrostatic discharge

15kV air, 8kV contact

Power specifications

Item

Description

Operating voltage

PoE-PD: 48-57VDC

Operating current

PoE-PD: 500mA at 48V

42

ExtremeWireless™ AP560i Access Point

Summary of Contents for ExtremeWireless AP560i















































Reviews:

No comments