Extreme Networks ExtremeWireless AP302W Installation Manual Download Page 15 | Manualshive

Page: 15 / 48

Extreme Networks ExtremeWireless AP302W Installation Manual Download Page 15

AP302W Power Source

Learn about the access point power source and the power ports usage.

Power source

Description

PSE port (up to 12.5 W) USB port (2.5 W)

PoE at 802.3at

802.3at is provided

through ETH0

Yes

Yes

802.3af

802.3af is provided

through ETH0

No

Yes

External 12 VDC power

supply (optional;

ordering part #37215-

PWR 12 VDC, 2A, 2.5

mm x 5.5 mm

connector)

Power is provided

through an external DC

power supply plugged

into an AC source

No

Yes

Note
PoE power is disabled when external power supply is used.

Status LED Activity and Light Sensor

Details about access point status LED activity and front face light sensor.

The light sensor is located in the front face of the access point but is not visibly marked. The status LED
is located at the bottom of the access point and conveys the access point operational status for system
power. For more details about access point front and rear features and port information, see

Table 7: Status light activity

Status light color

Activity

Description

Green

Steady

The device has a Control and Provisioning of

Wireless Access Points (CAPWAP) connection to

ExtremeCloud IQ and is operating normally

Slow blinking

The device has a CAPWAP connection to

ExtremeCloud IQ, but is operating on 802.3af

power instead of 802.3at power

Amber

Steady

The device is initializing, rebooting, or is running

without a CAPWAP connection

Slow blinking

The device has no CAPWAP connection to

ExtremeCloud IQ, and is operating on 802.3af

power instead of 802.3at power

Fast blinking

The device is upgrading it's IQ Engine firmware

Dark

None

Power is off or the status indicator is disabled

AP302W Overview

AP302W Power Source

ExtremeWireless™ Access Point AP302W

15

«
...
13
14
15
16
17
...
»

Summary of Contents for ExtremeWireless AP302W

















































Reviews:

No comments