background image

Assembly Manual / Airframe – 75” Extra 330 LT

Thank you for purchasing this 3DHobbyShop by Extreme Flight ARF RC aircraft. If you have 
any issues, questions, concerns or problems during assembly, please contact our tech 
department at: 

[email protected]

 or 770-887-1794 10am-5pm Eastern Monday thru 

Friday.

SAFETY in Assembly

During assembly of this aircraft, you will be asked to use sharp knives and hobby adhesives. 
Please follow all safety procedures recommended by the manufacturers of the products you use,
and always follow these important guidelines:
ALWAYS protect your eyes when working with adhesives, knives, or tools, especially power 
tools. Safety glasses are the best way to protect your eyes.
ALWAYS protect your body, especially your hands and fingers when using adhesives, knives, 
or tools, especially power tools. Do not cut toward exposed skin with hobby knives. Do not 
place hobby knives on tables or benches where they can roll off or be knocked off.
ALWAYS have a first-aid kit handy when working with adhesives, knives, or tools, especially 
power tools. ALWAYS keep hobby equipment and supplies out of the reach of children.

SAFETY in Flying

This is NOT a toy! It is a very high-performance RC airplane capable of high speeds and 
extreme maneuvers. It should only be operated by a competent pilot in a safe area with proper 
supervision.
ONLY fly your aircraft in a safe, open area, away from spectators and vehicles and where it is 
legal to fly. NEVER fly over an unsafe area, such as a road or street.

NEVER fly near overhead power or utility lines. If your airplane ever becomes stuck in
a line or a tree DO NOT attempt to retrieve it yourself. Contact the authorities for
assistance in retrieving your aircraft. Power lines are DANGEROUS and falls from
ladders and trees CAN KILL!

Never fly too close to yourself or spectators.

Spinning propellers are DANGEROUS!
Never run your motor inside a house or building with the propeller attached Remove the
prop for safety. Always fly within your control.

Always follow manufacturers instructions for your radio system.

Always preform a pre-flight check of  your aircraft to be certain of the aircraft's
airworthiness.

Always obtain proper insurance before flying.  Always fly model aircraft in accordance
with the Academy of Model Aeronautics (AMA) Safety Code.  Visit the AMA's website
at 

www.modelaircraft.org

 for more information.

Summary of Contents for Extra 330 LT
































Reviews: