manualshive.com logo in svg

Extech Instruments 382860, Instruction Manual, Page: 15 / 16

Share
Download
Extech Instruments 382860 Instruction Manual Download Page 15

15                                     382860       Ver. 1.5    2/01

 

 
9.2.2 Using the Windows Software 

Follow these steps to install and run the Windows software  

Note:

 The following steps assume a basic knowledge of Microsoft Windows. This 

software requires Microsoft Windows, Version 3.1 or later and a VGA or EGA 

display.  

1.  Start your computer and run Windows.  

2.  Insert the supplied diskette in your computer’s 3 ½-inch floppy drive.  

3.  For Windows 3.1 go to Program Manager and pull down the FILE menu. 

Select RUN. 

4.  For Windows 95, choose RUN from the START menu.  

5.  At the prompt, type:  

6.  a:\scope\setup (ENTER) (if you placed the diskette in Drive A) or 

b:\scope=setup(ENTER) (if you placed the diskette in Drive B) 

7.  Follow the on-screen prompts to complete the installation.  

8.  To run the program, double-click the SCOPE-VIEW icon, Follow the on-

screen help for specific operation instruction. Also, refer to the README file 

in the diskette’s SCOPE subdirectory for operation hints.  

 

 

10. MAINTENANCE 

 

10.1 Fuse Replacement 

Remove power to the meter and removal all connected cables and probes. Use a 

suitable Phillips screwdriver to carefully open the case. Remove the defective 

fuse(s) and replace it with a new one of the same type and nominal current (0.8A 

fast blow, 250 V); usual name: F 0.8A/250A or F 800Ma/250V. For the amperage 

range 20 A ultra rapid, 250V; usual name F 12A/250V (BUSSABC12). After the 

fuse has been exchanged close the cabinet. 

10.2  Battery replacement

 

Remover power to the meter and disconnect any cables or test leads. Open the 

battery compartment by removing the rear battery compartment screw with a 

Phillips screwdriver. Exchange battery and reinstall the battery compartment 

cover. 

 

( 

Tech Support Hotlines 

781-890-7440 ext. 200 

[email protected]

 

www.extech.com 

 
 

Summary of Contents for 382860

















Reviews:

No comments