manualshive.com logo in svg

Extech Instruments 382860, Instruction Manual, Page: 10 / 16

Share
Download
Extech Instruments 382860 Instruction Manual Download Page 10

10                                     382860       Ver. 1.5    2/01

 

2.  Connect the test-leads to the device under test. Ensure that all power is 

removed from devices under test. Auto Range selects the appropriate range 

automatically. 

3.  Normally the resistance of the test-leads can be disregarded (approx. 0.1 to 

0.2 Ohm). However, this small value can cause inaccuracy in the 400 Ohm 

range. To determine the error before measurement, short the test-lead tips 

and read the resistance value on the display. Subtract this value from 

readings to cancel lead resistance errors. 

4.  During resistance tests, make sure that the contact between test leads and 

circuits is optimized. Make sure the test points are free of dirt, oil or solder 

flux, etc. since these may seriously influence the measurement. 

5.  For resistance measurements >4M, the display will take several seconds to 

stabilize.  

6.  The left-most sub-LCD updates one second later than the main LCD, the 

middle sub-display 2 seconds later and the right-most sub-display 3 seconds 

later.  

6.5 Diode Test 

Attention: During diode tests, ensure that components and circuits under test are NOT 

powered. All existing capacities must be discharged. 

1.  Set the Rotary Switch to the diode symbol position. The diode icon will be 

displayed. Manual range selection is not possible during diode tests. 

2.  Connect the test-lead tips to the object under test. The RED probe-tip 

connects to the anode of the device under test and the BLACK test-lead tip 

connects to the cathode. 

3.  A diode’s forward voltage should measure approx. 0.25 V (Germanium) or 0.7 

V (Silicon), if the diode is GOOD. 

4.  Reverse the probe-tips (Red to the cathode and Black to the anode) to check 

the diode’s reverse status. 

5.  If  “OL” (overload) is displayed, the diode is open or measures above 2.0 V.  If 

a value between 0 V and approx. 2.0 is displayed, then a good forward 

voltage drop exists. 

6.  During diode tests the center sub-display indicates GOOD if the diode is o.k.  

If the diode is defective (short circuit) or low resistance short then SHORT is 

displayed. If the diode is defective due to high resistance or if the test leads 

are accidentally reversed (red to cathode and black to the anode) then 

“OPEN” for (open circuit) is displayed. 

NOTE: Checking LED components in Diode Test mode 

The meter’s test voltage in diode test mode is sufficient to “illuminate” most  

(low current) LEDs. If the LED has an operating voltage of more than 2.0 V, 

the meter will falsely indicate that the LED is defective when it actually may be 

good. 

 

6.6 Frequency Measurement 

Attention: Observe the max. input limits. Never connect voltages over 750 VDC/VAC 

rms. It is hazardous to touch the terminals or probe tips when measuring voltages > 

25VAC/35 VDC. Disconnect the test-leads from the contact points when measuring 

voltage (over 25 VAC or 35 VDC) and before changing the meter function and range  

1.  Set the rotary function switch to the “FREQ” position and insert the test leads 

to the meter 

2.  Connect the test-lead tips to the frequency source under test (generator, etc.). 

For the best accuracy, the use of BNC-Cables is strongly recommended. 

During frequency measurements, the right sub-display shows the dB-value of 

the AC voltage, the middle sub-display shows the AC voltage “V” and the 

main display: the present input value (frequency).

 

 

Summary of Contents for 382860

















Reviews:

No comments