6
5
1
AUFBAU
Anleitung
Vers. 1.0 / 07.12.22
EX
-
46028
Switzerland:
EXSYS Vertriebs GmbH
Dübendorfstrasse 17
8602 Wangen
www.exsys.ch
Germany:
EXSYS Vertriebs GmbH
Industriestrasse 8
61449 Steinbach
www.exsys.de
DRIVER INSTALLATION
Windows 2000 / XP / Vista / 7 / 8.x / 10 / 11 / Server 20xx
After the hardware installation is completed, the operating system automatically detects the EX
-
46028 and shows you a new
„
Serial PCI
-
Port
“
. Now insert the driver CD into your CD
-
ROM
drive (e.g. drive D:) and update the driver for the "Serial PCI
-
Port" in the Device Manager. For
this purpose, please select the correct driver, which can be found in the following folder
„
SERIAL&PARALLEL/XR17V35X(485)/XR17V358_8S_16S
“
.
Now select the folder of your
operating system and install the driver (see picture). Follow the installation instructions and
complete the installation.
Important!
Restart your PC after the installation.
CHECK INSTALLED DRIVER
Open the
>Device
-
Manager<
. Now you should see at
„
Ports (COM & LPT)
“
and at
„
Mutlifunction adapter
“
the following new Entries:
If you see these or similar entries, the card is installed correctly.
HARDWARE
INSTALLATION
Please note the following installation instructions. Because there are large differences between the
PC
’
s, we can give you only a general installation instructions for the EX
-
46028. Please refer your
computer
’
s reference manual whenever in doubt.
1.
Turn off the power to your computer and any other connected peripherals.
2.
Remove the mounting screws located at the rear and/or sides panels of your Computer and
gently slide the cover off.
3.
Locate an available PCI
-
Express expansion slot and insert the card. Make sure that the card
is plugged in correctly.
4.
Then attach the card with a screw to the rear panel of the computer.
5.
Gently replace your computer
’
s cover and the mounting screws.
6.
Finally, connect the included octopus cable to the 68
-
pin VHDCI connector of the EX
-
46028.
DRIVER INSTALLATION
Linux
After the hardware installation is completed, the operating system automatically recognizes the
EX
-
46028. Now insert the driver CD into your CD
-
ROM drive (e.g. drive D:) and open the folder
„
SERIAL&PARALLEL/XR17V35X(485)/XR17V358_8S_16S
“
. The drivers for your Linux
system are located in the
„
Linux
“
folder (see picture).
Important!
Restart your PC after the
installation.
BESCHREIBUNG & TECHNISCHE DATEN
Kompatibilität:
PCI
-
Express x1 bis x16
Betriebssysteme:
Windows 2000 / XP
/
Vista / 7 / 8.x / 10 / 11 / Server 20xx / Linux
Anschlüsse:
8x 9
-
Pin D
-
Sub Seriell Stecker
Lieferumfang:
EX
-
46028, Oktopus Kabel, Low Profile Bügel, Treiber CD,
Anleitung
Zertifikate:
8x 9
-
Pin D
-
Sub Seriell Stecker
Die EX
-
46028 ist eine seriell RS
-
232 PCI
-
Express Karte. Sie ist mit acht seriellen FIFO 16C550
Anschlüsse für den Anschluss von High
-
Speed seriellen RS
-
232 Peripherie Geräten (z.B.
Modem, Plotter, Drucker, Scanner usw.) ausgestattet. Diese werden mittels eines Oktopus
Kabels zur Verfügung gestellt, welches an die 68
-
Pin VHDCI Buchse der EX
-
46028 ange-
schlossen wird. Die EX
-
46028 unterstützt alle PCI
-
Express Slots von x1 bis x16. Der serielle
PCI
-
Express Bus unterstützt optimal die Leistung des schnellen Exar Chipsatz. Die Karte
gewährleistet so eine sichere Datenübertragung und exzellente Performance von bis zu 115K-
Baud/s für jedes angeschlossene serielle Gerät! Es ist nicht möglich die I/O Adressen und
Interrupts manuell einzustellen, da die Einstellungen der Karte vom System (BIOS) und beim
installieren des Betriebssystems automatisch vorgenommen werden.
ANSCHLÜSSE
9
-
Pin D
-
Sub Seriell Stecker:
9
-
Pin D
-
Sub Seriell Stecker
Pin
Signal
Pin
Signal
Pin
Signal
1
CDC
4
DTR
7
RTS
2
RXD
5
GROUND
8
CTS
3
TXD
6
DSR
9
RI
