6
5
1
Die EX
-
12003 ist eine USB 3.1 (Gen2) PCI
-
Express (Gen3) Karte. Sie ist mit 2 externen USB
3.1 (Gen2) C
-
Ports ausgestattet, die jeweils 1,5A Strom zu Verfügung stellen. Die EX
-
12003
unterstützt die volle Leistung von 1,5A an beiden externen Ports ohne das Sie zusätzlichen
Strom vom PC
-
Netzteil benötigen. Zusätzlich ist es möglich das USB Kabel an die externen
Ports der Karte zu verschrauben. Sie unterstützt alle PCI
-
Express Slots von x2 bis x16. Der
serielle PCI
-
Express Bus unterstützt optimal die Leistung des schnellen ASMedia Chipsatz. Die
EX
-
12003 gewährleistet so eine sichere Datenübertragung und exzellente Performance von bis
zu 10Gbit pro Sekunde! Die EX
-
12003 unterstützt alle USB Anschlüsse von 1.1 bis 3.1.
ANSCHLÜSSE
BESCHREIBUNG & TECHNISCHE DATEN
AUFBAU
Anleitung
Vers. 1.0 / 06.03.2018
EX
-
12003
Kompatibilität:
PCI
-
Express (Gen3) x2 bis x16
Betriebssysteme:
Windows XP/ Vista/ 7/ 8.x/ 10/ Server 20xx/ Linux
Anschlüsse:
2x USB 3.1 (Gen2) C
-
Buchse extern (verschraubbar)
Lieferumfang:
EX
-
12003, Low Profile Bügel, Treiber CD, Anleitung
Zertifikate:
J3 & J4:
2x externe USB 3.1 (Gen2) C
-
Buchse
(verschraubbar)
J3 & J4:
Hinweis!
Durch die doppel Belegung der Pin’s, kann der USB Typ
-
C Stecker beidseitig in die
Buchse gesteckt werden.
HARDWARE
INSTALLATION
DRIVER
INSTALLATION
DRIVER
INSTALLATION
Windows XP/ Vista/ 7/ Server 2003 & 2008 R2
After starting Windows is recognizes a new „
USB (Universal Serial Bus)
-
Controller
“.
Start the
„
setup.exe
“ file which is in the „
ASM3142
“ folder (see picture):
Follow the installation instructions and complete the installation.
Windows will now install automatically you right driver for your particular operating system. After
the installation the operating system detects the card and automatically install them. If this fails
or you would like to install the driver manually, you can use the driver which is located in the
folder „
Driver
“.
CHECK INSTALLED DRIVER
Open the >
Device manager
<. Now you should see at „
USB
-
Controller
“
the following new entry's:
If you see this or a similar information the device is installed correctly.
Please note the following installation instructions. Because there are large differences between the
PC’s, we can give you only a general installation instructions for the EX
-
12003. Please refer your
computer’s reference manual whenever in doubt.
1.
Turn off the power to your computer and any other connected peripherals.
2.
Remove the mounting screws located at the rear and/or sides panels of your Computer and
gently slide the cover off.
3.
Locate an available PCI
-
Express expansion slot and insert the card. Make sure that the card
is plugged in correctly.
4.
Then attach the card with a screw to the rear panel of the computer.
5.
Gently replace your computer’s cover and the mounting screws.
Windows 8.x/ 10/ Server 2012 R2 & 2016
After the hardware installation, the operating system will recognize the device automatically and
install the drivers. If this fails and you need to install the driver manually, you can use the driver
which is located in the folder for your operating system (see picture).
For Server 2012 R2 please use the Windows 8 driver and for Server 2016 please use the
Windows 10 driver.
CHECK INSTALLED DRIVER
Open the >
Device manager
<. Now you should see at „
USB
-
Controller
“
the following new entry's:
If you see this or a similar information the device is installed correctly.
Linux
After the hardware installation, the operating system will recognize the device automatically and
install the drivers.
CHECK INSTALLED DRIVER
Now you should see the following new entry:
If you see this or a similar information the device is installed correctly.
