manualshive.com logo in svg

Expert Electronics ColibriDDC, User Manual

Share
Download
Expert Electronics ColibriDDC User Manual Download Page 48

48

ColibriDDC User Manual

© 2022 Expert Electronics

ExpertSDR2 SOFTWARE DESCRIPTION

·

I mage menu – Image presets menu (Forrest, Bubbles, Space, Water, User).

Pick the required image from the menu or lock one of your own images.

·

Bright ness – Background image brightness slider.

Set the required background image brightness.

·

User image - Choose the required image to be displayed on the background.

Press  the  Open  button,  in  the  opened  window  choose  the  image  file  to  set  as  the

background.

Note:

·

 If the image file wasn't chosen previously via  the  Open button, then if you choose  the  User
image in the presets list it'll open the window to choose the image file.

·

 Supported files types: png, jpg, jpeg, bmp.

3.3.4

CAT menu

In  the  CAT  menu,  you  can  see  the  CAT-system  settings.  CAT-system  is  the  transceiver's

exchange interface with external devices and software.

CAT-interface is used for control the receiver from a third-party software. This could be contest

logs,  digital  modes  decoder-software,  SAT-tracker  etc.  RX1  and  RX2  have  independent

settings and could be controlled separately via the CAT-protocol.

There are two ways to use the ColibriDDC with an external transceiver:

3.3.4.1

ECATv1

ExpertSDR2 software has the ECATv1 protocol, use it to synchronize the ColibriDDC and your

transceiver via 

RigSync

 software.

ECATv1  -  exchange  protocol  compatible  with  TS-480  transceiver.  This  protocol  allows  to

exchange data with an external devices and software via COM-port.

Summary of Contents for ColibriDDC






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands