background image

- 28 -

Turn setscrew out (counterclockwise) to decrease force on lever required to shift
gears. Factory setting is to turn setscrew all the way in then back out 1-1/2 turns.

IMPORTANT: Screwing setscrew in too far will prevent the transmission
from shifting

.

5.2.11  Wheel drive spring tension adjustment:

It may be necessary to increase wheel drive belt tension under certain
conditions such as, wet grass, hilly terrain, or while pulling a sulky.

a)  Stop engine and remove spark plug wire(s).

b)  Disengage neutral lock/park brake latches and release drive levers to

lower spring force.

c)  Remove the 5/16-18 whizlock nut securing the adjustment  bolt to the

drive wheel shield. Locate bolt assembly in the desired position as follows

Position A - Normal Conditions
Position B - More Severe
Position C - Most Severe

NOTE: Lever force is lowest with bolt assembly in Position A and will increase
in Positions B and C (See Figure 16).

FIG. 16

DRIVE BELT TENSION

ADJUSTMENT POSITIONS

5.2.12  Adjust Throttle Lever Tension (B&S Engines only):

a) 

Stop engine and remove spark plug.

b)

Tension in throttle levers can be increased or decreased by adjusting the
tightness of the lever pivot bolt which is located under the console.

6. WASTE DISPOSAL

6.1 MOTOR OIL DISPOSAL

Engine oil is a pollutant to the environment.  Dispose of used oil at a certified
recycling center or according to your state and local regulations.

7. TROUBLE SHOOTING

7.1 MOWER PULLING LEFT OR RIGHT.

a) 

Check idler arm pulleys and drive sheaves for mud and/or grass buildup.
Check for proper scraper position. See 5.2.6.

b) 

Check to be sure idler arms pivot freely, if not lubricate idler pivots.

c) 

Check for worn drive belts.

NOTE: Wheel drive belts should be replaced as a set.  A new belt should
not be mixed with a worn belt.

d) 

Check drive linkage adjustment - See 3.11

For Exmark Mower Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

Summary of Contents for Metro HP













































Reviews: