manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 843

Glossary

Power Blazer

833

SONET/DSn/SDH/PDH

SONET Numbering Convention

The module supports the Timeslot (default) and hierarchical two-level 
numbering conventions as per GR-253.

Hierarchical Notation:

The module supports numbering SONET high order path STS-1s and STS-3c 
using the two-level “STS-3#,STS-1#”convention in an OC-N. For example: 
STS-1 [2,3].

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands