manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 651

Test Functions

Power Blazer

641

FEAC

FEAC 

The Far-End Alarm and Control signal (FEAC) provides Communication 
Channel capability over a DS3 in a network applications using C-bit Parity 
configuration (see page 333). 

From the test menu, tap 

Functions

, and the 

FEAC 

tab. 

Generated Messages 

Allows configuring and sending alarms/status information and control 
signals (loopback commands) to other network elements. 

Alarm/Status and Unassigned 

Codeword

 allows the selection of the codeword alarm/status to be 

generated either manually or continuously. 

The FEAC message format is a 16 bit codeword 
(0xxxxxx0 11111111) with the rightmost bit transmitted first. The 
0xxxxxx0 represents the message codeword. 

Mode

 is the alarm/status injection mode: 

Manual

 or 

Continuous

. 

Codeword

DS3 Equipment Failure SA (00110010)

Single DS1 LOS (00111100)

User Defined (00100000)

DS3 Loss of Signal (LOS) (00011100)

DS1 Equipment Failure NSA 
(00000110)

User Defined (00100010)

DS3 Out-of-Frame (00000000)

User Defined (00000010)

User Defined (00101000)

DS3 AIS Received (00101100)

User Defined (00000100)

User Defined (00101110)

DS3 Idle Signal Received (00110100)

User Defined (00001000)

User Defined (00110000)

DS3 Equipment Failure NSA (00011110)

User Defined (00001100)

User Defined (00111110)

DS3 NUI Loop Up (00010010)

User Defined (00010000)

User Defined (01000000)

DS3 NUI Loop Down (00100100)

User Defined (00010100)

User Defined (01111010)

Common Equipment Failure NSA (00111010) User Defined (00010110)

User Defined (01111100)

Multiple DS1 LOS (00101010)

User Defined (00011000)

User Defined (01111110)

DS1 Equipment Failure SA (00001010)

User Defined (00011010)

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands