manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 632

Test Functions

622

88000 Series

40/100/200/400G Advanced - Lanes Mapping & Skew

Laser ON/OFF

Allows activating the laser control per optical lane or for all lanes.

Optical lane numbers are from 

0

 to

3

 or 

0

to

7

 depending on the 

selected interface/rate.

All Lanes

 check box, when selected, applies the change(s) to all 

optical lanes at once.

Optical Lane

 indicates the optical lane numbers and 

All

 which 

represents the setting for all optical lanes when the 

All Lanes

 

check box is selected.

Laser

 check box, when selected, indicates that the corresponding 

optical laser lane is activated and emitting an optical laser signal. 

Skew Alarm Threshold (bits) 

Allows setting the threshold value that will be used to declare a skew alarm 
(see 

Ex. Skew

 on page 440).

Default

 button restores the default alarm threshold value. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands