manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 630

Test Functions

620

88000 Series

40/100/200/400G Advanced - Lanes Mapping & Skew

Default/Random/Manual Mapping

Allows changing the PCS/Logical lane mapping that will be used for the 
test. Not available with 100 GbE client in OTU4. 

Default Mapping

 sets the TX mapping to the default numerical order 

value which corresponds to the ascending PCS/Logical lane order. 

Random Mapping

 sets the TX mapping in a random order. Each time 

the button is tapped, random alignment markers are assigned to each 
PCS/Logical lane. 

Manual Mapping

 allows setting the TX mapping manually. 

PCS/Logical Lane/Lane Marker 

and 

Assigned Status

: 

The 

PCS/Logical Lane/Lane Marker

 buttons allow assigning the 

corresponding Lane Marker to the selected PCS/Logical or 
xGAUI-y/CAUI/XLAUI/Physical Lane mapping (the one pointed by 
the arrow). The 

Assigned Status

 column displays a check mark 

next to the assigned PCS/Logical Lanes. Range is from 

0

 to 

15

 for 

400G, 

0

 to 

7

 for 200G, 

0

 to 

19

 for OTU4/100G, and 

0

 to 

3

 for 

OTU3/OTU3e1/OTU3e2/40G. 

PCS/Logical Lane

 and xGAUI-y/

CAUI/XLAUI/Physical Lane

 

columns indicate the target PCS/Logical to 
xGAUI-y/CAUI/XLAUI/Physical mapping. 

Clear All

 clears the PCS/Logical to xGAUI-y/CAUI /XLAUI/Physical 

Lane assignments.

OK

 accepts the new PCS/Logical to xGAUI-y/CAUI/XLAUI/Physical 

lane mapping. All target PCS/Logical Lane fields must contain an 
assignation, including duplicates, to give access to the 

OK

 button.

Note:

A PCS/Logical Lane marker can be assigned more than once. If this is the 
case, a red background is used to highlight all occurrences of this 
PCS/Logical Lane marker. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands