EXFO Power Blazer 88200NGE User Manual Download Page 615

Page: 615 / 887

Test Results

Power Blazer

605

Traffic - Graph

Traffic - Graph

From the

Test

menu, tap

Results

Traffic

, and the

Graph

tab.

Note:

For

Dual Port

topology select the port to be displayed.

The graph displays the received line utilization. The X axis shows the time
in seconds while the Y axis shows the percentage utilization.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands