manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 45

Graphical User Interface Overview

Power Blazer

35

Title Bar

The following status are also displayed: 

Battery/AC icons, available on FTB platforms, indicate the battery level 
and if the platform is connected to an AC power source. Refer to the 
platform user guide for more information. 

Date and Time indicate the current date and time. 

Title Bar 

The Title Bar displays the module’s slot number in brackets, the software 
application name and the minimize, maximize, and close buttons. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands