EXFO Power Blazer 88200NGE User Manual Download Page 438

Page: 438 / 887

Test Results

428

88000 Series

Alarms/Errors Overview

IP/UDP/TCP

Errors



IP Chksum

(IP Checksum)

: The IP datagrams received have invalid IP header checksum. Only

available for IPv4.



UDP Chksum

(UDP Checksum)

: The UDP segments received have invalid UDP checksum.



TCP Chksum

(TCP Checksum)

: The TCP segments received have invalid TCP checksum.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands