EXFO Power Blazer 88200NGE User Manual Download Page 424

Page: 424 / 887

Test Results

414

88000 Series

Alarms/Errors Overview

Error



Symbol

(FC 1X/2X/4X/8X)

: Invalid code-group is detected in the code.



Block

(FC 10X/16X)

: The number of frames received with an errored block condition.



66B Block

(FC 32X)

: The number of frames received with an errored block condition;

excluding frames in LOCWS.



FEC-CORR-CW

(FC 32X)

: FEC codeword that contains errors and were corrected; excluding

frames in LOCWS.



FEC-UNCOR-CW

(FC 32X)

: FEC codeword that contains error and were not corrected;

excluding frames in LOCWS.



Pre-FEC-SYMB

(Pre-FEC Symbol; FC 32X)

: FEC symbol errors are corrected and counted once for each 10-bit

symbol; excluding frames in LOCWS.



FCS

(Frame Check Sequence)

RX/TX

: Frames with an invalid FCS are received/generated.



Oversize

: The number of received FL-2 frames larger than 2148 bytes with a

valid FCS.



Undersize

: FL-2 frames smaller than 36 bytes with a valid FCS.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands