EXFO Power Blazer 88200NGE User Manual Download Page 414

Page: 414 / 887

Test Results

404

88000 Series

Alarms/Errors Overview

Alarms

Note:

Only AIS is available when the framing is set to Unframed.



AIS

(Alarm Indication Signal)

: An unframed all-ones signal is received.



LOF

(Loss Of Frame)

: Four consecutive incorrect frame alignment signals is received.



RAI

(Remote Alarm Indication)

: Bit 13 of a framed E4 is set to “1”.

Errors



FAS

(Frame Alignment Signal)

: Bits 1 to 12 of the first frame differ from 111110100000.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands