manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 29

Power Blazer

19

4

Physical Interfaces and LEDs

This section describes all connectors (ports) and LEDs available on the 
88000 Series. 

FTBx-88200NGE 

FTBx-88260 and Transceiver Systems 

Note:

The FTBx-88260 module with TA-SFP28 transceiver systems are shown 
below as examples for connector location purposes. 

C

AUTION

To prevent exceeding the maximum input/output power level, 
please refer to this product’s technical specifications at 
www.exfo.com. 

CFP4

1

 

QSFP

1

 EXT 

LCK 

REF OUT 

SFP+

1

 

1. Laser radiation emitted from this port when LASER LED is on. 

1. Laser radiation emitted from this port when LASER LED is on. 

Port A 

Port B 

FTBx-88260

 

Port A1

1

 

TA-SFP28

Port A2

1

 Port 

B1

1

 Port 

B2

1

 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands