Home
/
EXFO
/
Power Blazer 88200NGE
/
User Manual

EXFO Power Blazer 88200NGE, User Manual

Share

Page: 243 / 887

EXFO Power Blazer 88200NGE User Manual Download Page 243

Test Setup - Test Configurator, Timer, and System

Power Blazer

233

Interface

Physical Interface

For parallel interfaces, the following information is displayed for each
optical lane. Not supported when

PHY Type

is set to

DAC

.



Optical Lane

indicates the optical lane number.



Laser

indicates the status of the laser:

ON

with the laser pictogram

(emitting an optical laser signal) or

OFF

.



TX Power (dBm)

indicates, when supported, the transmit power level

of the optical lane/laser in dBm.



Wavelength (nm)

indicates, when supported, the detected

wavelength.



RX Power (dBm)

indicates, when supported, the current received

power level of the optical laser/lane in dBm.

Green: Power level in range.
Yellow: Power level out-of-range.
Red: Loss of signal or power level is close to damage.
Gray: Invalid operational range value or not available/supplied by the
transceiver.

For parallel interfaces, in the

Test Configurator

-

Interface

block,

LO

and

HI

report respectively the current lowest and highest RX power

levels from any lane.

Optical Interface

Optical Lane Number

40GE (4 Lanes) [41.25 Gbit/s]
100GE (4 Lanes) [103.125 Gbit/s]
200GE (4 Lanes) [212.5 Gbit/s]
400GE (4 Lanes) [425 Gbit/s]

0 through 3

400GE (8 Lanes) [425 Gbit/s]

0 through 7

«
...
241
242
243
244
245
...
»

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands