manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 220

Test Setup - Test Configurator, Timer, and System

210

88000 Series

FlexE Group

FlexE Group 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, and on the 

FlexE Group

 protocol block. 

Note:

Only one client is supported in the FlexE Group. 

FlexE Status 

Indicates the global FlexE group status: up (green arrow) or down (red 
arrow). 

Calendar Mismatch 

Indicates if the received calendar differs from the one expected using the 
following colors: red for mismatch; green for match; otherwise it is gray. 

FlexE Group Number 

Allows associating a number to the FlexE Group: 

0

 to 

1048575

. 

Calendar 

Allows selecting the calendar 

A

 or 

B

 that is used for mapping/demapping 

the FlexE clients into/from the FlexE group. 

Table 

Client ID

 indicates the client identification number. 

Size

 indicates the size of the client in Gbit/s. 

Link

 indicates the client link status: link up (green arrow) or link down 

(red arrow). 

Qty of Clients

 indicates the number of clients assigned to the FlexE 

group. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands