manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 188

Test Setup - Test Configurator, Timer, and System

178

88000 Series

Device Under Test (iOptics)

More

 gives additional transceiver system/module information and 

settings. 

Transceiver System

 tab: See 

Transceiver System (TA/TA4)

 on page 364.

Device Under Test

 tab: 

Parameters

 are retrieved from the transceiver (see 

Parameters

 on 

page 164). 

Lasers OFF at Start-Up

 allows turning off all lasers automatically 

when starting the module or when switching from one test 
application to another. This check box is cleared by default. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands