manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 720

Glossary

708

88000 Series

Ethernet Cables

Ethernet Cables 

Minimum Category 3 cable is required for 10Base-T connection while 
Category 5 cable is required for 100Base-TX and 1000Base-T connections.

Maximum cable length (between two nodes) for 10Base-T, 100Base-TX, or 
1000Base-T connection is 328 feet (100 meters).

Straight Through Cable (10/100 Mbit/s) 

An Unshielded Twisted Pair (UTP) straight through cable is required to 
connect a 10Base-T/100Base-TX module port to a layer 1 or 2 device 
(ex: HUB, switch).

Crossover Cable (10/100 Mbit/s)

An Unshielded Twisted Pair (UTP) crossover cable is required to 
connect the 10Base-T/100Base-TX module port to a layer 3 device (ex: 
router).

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands